MANUALES TALLER BARCOS

CLAAS JAGUAR SYSTEM FAULT CODES CIS

 

**************************************************
**Code Module Fault Operating state Troubleshooting**
 **************************************************

E-1 Device CAB
oil pressure engine too poor
 
E-2 device CAB
Oil Level engine too low
 
E-3 Unit CAB
Water pump defective Charging Control lightsand goes out.
Test drive water pump and generator.
Check control charge on generator
.
The apparatus E-4 CAB
Temperature cooling water too high
 
The device E-5
CAB
hydraulic temperature Coil too high
 
The device E-6 CAB
Tighten the handbrake
 
E-8 Elektrogid
ravlicheski
First drive running of the EFA
Wrong voltage potentiometer supply of movement
 
E-11 apparatus CAB
pressure hydraulics
Coil or oil level is too low
 
E-12 apparatus
CAB
Temperature charge air too high
 
E-13 Metal detector ESR
defective
 
E-14 ESR metal detector
interrupt
 
E-15 apparatus
CAB
Reserve SAB
 
E-16 ESR still connected
adapter box SFM
(Note: SFM =
self-propelled mower)
When necessity check configuration (SFH or SFM).

E-17 numbers of revolutions ESR Sensor
feeder defective
Check plug to compound sensor and cable compound.
 
E-18 numbers of revolutions ESR Sensor
feeder defective
Check plug to compound sensor and cable compound.
 
E-19 apparatus CAB
Hydraulic drive motor
Coil not complies configuration
 
E-20 Elektrogid
ravlicheski
First drive
running
of the EFA
new module EFA =>absolutely necessary potentiometer study movement of the lever
This message appears after installing a new EFA module when the ignition.
After learning potentiometers arm and hydraulic motion flow this message
no longer appears.
1. Study potentiometer movement of the lever
2. Study hydraulic flows through CDS system Hydraulic oil should have labor temperature.
meaning voltage
pressure sensors
should be <1.2 V.
 
E-25 ESR fault downstream
hydraulic pump
feeder
 
E-27 Elektrogid
ravlicheski
First drive
running
of the EFA
Defective valve output
PWM trailer brakes
 
E-30 In ESR Valves
stop permanently
energized
 
E-32 device
CAB
CAN-Bridge Module
defective
Check
power
module.
Check strength
landing and contact
conclusions.

E-33 ESR ESR module defective Check
power
module.
Check strength
landing and contact
conclusions.
 
E-34 AutoContour
CAC
module outline
faulty system
Check
power
module.
Check strength
landing and contact
conclusions.
 
E-36 module GGS GGS Defect Test
power
module.
Check strength
landing and contact
conclusions.
 
E-37 Elektrogid
ravlicheski
First drive
running
of the EFA
EFA faulty module Emergency stop:
During this work
It indicates a defect
power module output.
It should be shut down.
The movement of the machine
no more
provided
possible.
Turn off the machine and
restart,
if the fault
no more
It appears,
in another module
procedure, otherwise
If not, replace
module.
 
E-38 KSR Control Unit
valve defective
 
E-39 ATP reserve, autopilot
 
E-40 Elektrogid ravlicheski
First drive running of the EFA
Faulty valve hydraulic pump
Emergency mode:
The machine moves only
reversing at speeds
OK. 2 km / h at the 2nd
Transfer 1 km / h in the 1st
transmission.
When you identify short
the closure of the valve
It made an emergency
Stop the movement over
impossible.
flap
impossible
to govern:
Check
cable
Connect to
valve. Check the module output.
measure
resistance
coil range
values: 6 - 12 ohms
Check plug to compound valve.

E-41 Elektrogid
ravlicheski
First drive
running
of the EFA
Faulty
electromagnetic
hydraulic valve
engine
Limited
exploitation:
Stir until
Max. 7 km / h on the 1st
transmission,
ok.12 km / h on the 2nd
transfer
flap
impossible
to govern:
Check
cable
module connection to
the valve for a short
circuit or
breakage. Check
the module output.
measure
resistance
coil range
values: 6 - 12 ohms
Check
plug
to compound
valve.
 
E-42 Elektrogid
ravlicheski
First drive
running
of the EFA
Faulty third magnet
electromagnetic
valve
Emergency Stop:
The machine moves on
coast to stop,
further movement is not
provided
possible.
flap
impossible
to govern:
Check
cable
module connection to
the valve for a short
circuit or
breakage. Check
the module output.
measure
resistance
coil range
values: 6 - 12 ohms
Check
plug
to compound
valve.
 
E-43 Elektrogid
ravlicheski
First drive
running
of the EFA
Defect
electromagnetic
pump valve
motion ago
Emergency mode:
The machine moves only
forward at approx. 2
km / h at the 2nd transmission 1
km / h on the 1st gear
When you identify short
the closure of the valve
It made an emergency
Stop the movement over
impossible.
flap
impossible
to govern:
Check
cable
module connection to
the valve for a short
circuit or
breakage. Check
the module output.
measure
resistance
coil range
values: 6 - 12 ohms
Check
plug
to compound
valve.
 
E-44 device
CAB
Out of order
communication
engine system
No CAN bus to
module ADM.
The module works
wrong.
Check
power
modules. Check
cable trunk to
modules (terminals).
E-45 Grinder GGS
not in the initial position
E-46 Elektrogid
ravlicheski
First drive
running
of the EFA
Faulty
lever potentiometer
of movement
Emergency mode:
The car moves with
speed 1 km / hr only
in the forward direction.
(Identification of areas
movement through
neutral switch
position and the switch
Reverse)
Potentiometer
movement of the lever
It is in the form
double
potentiometer.
Signal
malfunction
issued
following cases:
Incorrect
polarity
potentiometers
movement, open
cable
complete,
defective
contact strip
potentiometer.
Remedy:
Check supply
voltage
potentiometer
motion check
plug
to compound
potentiometer.

 
E-Check 46
cable set
to module
potentiometer on
open or short
circuiting.
Potentiometer
Motion 2 issues
opposite
signal sum
with which the signal
potentiometer
Motion 1 is always
must have
permanent
value.
If the total
signal is not in
within 7.3 - 7.5,
the potentiometer
movement of the lever
defective.
Example:
Signal 1 = 4.0 V
Signal 2 = 3.4 V>
Amount: 4.0 + 3.4 = 7.4
B => potentiometer
order.
Signal 2 = 1.0 =>
Amount: 4.0 + 1.0 = 5.0
B => potentiometer
defective
measure
potentiometer.

 
E-47 Elektrogid
ravlicheski
First drive
running
of the EFA
exceeded tolerance
lever potentiometer
of movement
Unusual behavior
movement.
No, the final
speed.
Despite the return of
movement of the lever ago
speed reduction
initially not made
(Slow response).
Speedstar fur .:
Only the issue of a code,
the behavior of the motion is not
changes.
Potentiometer
movement of the lever
It is in the form
double
potentiometer:
permissible
meaning
potentiometer
Motion 1:
Neutral
Situation: 3,8 -
4.2V
Next: 6.9 - 7.3 in
Previous: 0.8 - 1.2 V
If there is a
excess
forward or values
back to
mechanical
end
positions of the lever
motion,
must
align
control system
potentiometer
movement of the lever.
Potentiometer
Motion 2 issues
opposite
signal sum
with which the signal
potentiometer
Motion 1 is always
must have
permanent
value.
If the total
signal is not in
within a predetermined
range,
lever potentiometer
of movement
defective.
 
E-48 in the feed ESR Metal
device
The delivery device
It stands load
metal detector.
Remove the metal.
Is not
fault in
sense of the word.
 
E-49 ESR Stop
slip
clutch consoles
STB is turned off. Post without
overload:
Check
cable set
and to console her.
Check sensor
rotation speed
prefix.
 
E-50 ESR does not recognize the adapter
SFM box
The module identifies the ESR
speed sensors
Rotation Disco 8500, but
5 are absent from
adapter box.
Female
compound:
Check 13
pin connector on the
driver site
(corrosion).
Open or short
closing
signal wire
to the ESR module.
 
E-51 apparatus
CAB
The level of coolant
the water is too low
Refuel
cooling water.
Cable set
or plug
cause short
short to ground.
 
E-52 ESR No recognition
rotation speed
feeder
Posted on
Fault can be
issued in multiple
without reversing
causes.
When submitting a feed
the device is switched off
after the issuance of reports
malfunction.
Check
plug
to compound
speed sensor
rotation.
Check 13
pin connector on the
driver site
(corrosion).
Open or short
closing
signal wire
to the ESR module.