top of page

NEW HOLLAND & CASE IH FAULT CODES


**********************
**TYPE CODE ERROR**

**********************

code error ENG 111 Engine Controller Failure - Hardware Failure
code error ENG 115 Engine Speed Sensor (8.3, 9 Liter) or Cam Sensor (15 Liter) is failed
code error ENG 121 Engine Position Sensor (8.3, 9 Liter) or Crankshaft Sensor (15 Liter) is failed
code error ENG 122 Boost Pressure Sensor voltage is too high
code error ENG 123 Boost Pressure Sensor voltage is too low
code error ENG 124 Boost Pressure level has exceeded the warning limit.
code error ENG 131 Decelerator or Hand Throttle (STD cab) Position potentiometer voltage is too high
code error ENG 132 Decelerator or Hand Throttle (STD cab) Position potentiometer voltage is too low
code error ENG 133 Decelerator (STD cab) Position potentiometer voltage is too high
code error ENG 134 Decelerator (STD cab) Position potentiometer voltage is too low
code error ENG 135 Oil Pressure Sensor voltage is too high
code error ENG 141 Oil Pressure Sensor voltage is too low
code error ENG 143 Oil Pressure level has fallen below the warning limit.
code error ENG 144 Coolant Temperature Sensor voltage is too high
code error ENG 145 Coolant Temperature Sensor voltage is too low
code error ENG 146 Coolant Temperature level has exceeded the warning limit.
code error ENG 147 Frequency Throttle Signal shorted high
code error ENG 148 Frequency Throttle Signal shorted low
code error ENG 151 Coolant Temperature level has exceeded the warning limit.
code error ENG 153 Intake Manifold Temperature Sensor voltage is too high
code error ENG 154 Intake Manifold Temperature Sensor voltage is too low
code error ENG 155 Intake Manifold Temperature level has exceeded the warning limit.
code error ENG 187 Sensor Supply 2 Voltage is too low.
code error ENG 191 A/C clutch driver shorted to ground when ON.
code error ENG 211 Communications problem with Armrest, Instrumentation, or Transmission Controllers
code error ENG 212 Oil Temperature Sensor Voltage is too high
code error ENG 213 Oil Temperature Sensor Voltage is too low
code error ENG 214 Oil Temperature Sensor Voltage is above normal range
code error ENG 219 Oil Level - remote reservoir is too low. Add oil.
code error ENG 221 Ambient Air Pressure Sensor Voltage is too high
code error ENG 222 Ambient Air Pressure Sensor Voltage is too low
code error ENG 223 CORS - Burn Valve Solenoid is shorted either low or high
code error ENG 227 Sensor Supply 2 Voltage is too high.
code error ENG 234 Engine Speed has exceed the overspeed warning limit.
code error ENG 235 Engine Coolant Level is low. Add coolant fluid.
code error ENG 237 External Speed Multi Unit Sync Command Input Data Incorrect.
code error ENG 241 Vehicle Speed Signal lost
code error ENG 242 Vehicle Speed Signal intermittent / tampering
code error ENG 243 Error detected in exhaust brake relay
code error ENG 245 Fan Clutch Voltage too low
code error ENG 254 Fuel Shutoff Valve Voltage too low
code error ENG 255 Fuel Shutoff Valve Voltage too high
code error ENG 259 Fuel Shutoff Valve mechanically stuck open.
code error ENG 263 Fuel Temperature Sensor voltage is too high
code error ENG 265 Fuel Temperature Sensor voltage is too low
code error ENG 268 Fuel Pressure in pump is not changing with operating conditions.
code error ENG 271 Front Pumping Control Valve current is low during ñclick testî
code error ENG 272 Front Pumping Control Valve current is high
code error ENG 273 Rear Pumping Control Valve current is low during ñclick testî
code error ENG 274 Rear Pumping Control Valve current is high
code error ENG 275 Front Pumping element is failed
code error ENG 276 Injection Control Valve current is out of range
code error ENG 277 Injection Control Valve is failed
code error ENG 278 Fuel Lift Pump is failed
code error ENG 279 Injection Control Valve current is out of range
code error ENG 281 Front Pumping element is failed
code error ENG 282 Rear Pumping element is failed
code error ENG 283 Engine Speed/Position Sensor supply voltage is too high
code error ENG 284 Engine Speed/Position Sensor supply voltage is too low
code error ENG 285 J1939 Parameter was set to be multiplexed, but not received (timeout error)
code error ENG 286 J1939 Parameter was set to be multiplexed, but not available from all sources (config error)
code error ENG 287 Multiplexing throttle parameter and a data error was received - data invalid
code error ENG 288 Multiplexing remote throttle parameter and a data error was received - data invalid
code error ENG 293 Hydraulic Fan Hydraulic Oil Temperature Sensor Voltage is too high
code error ENG 294 Hydraulic Fan Hydraulic Oil Temperature Sensor Voltage is too lowcode error ENG 295 Ambient Air Pressure data invalid
code error ENG 297 OEM Pressure Sensor Voltage is too high.
code error ENG 298 OEM Pressure Sensor Voltage is too low.
code error ENG 299 Engine Shutdown by other than keyswitch (i.e. via data bus command)
code error ENG 319 Real Time Clock in controller has lost power
code error ENG 328 Rear Pumping element is failed
code error ENG 329 CAPS Pump has an overpumping failure
code error ENG 338 Idle Shutdown Vehicle Accessory Relay Voltage is too high
code error ENG 339 Idle Shutdown Vehicle Accessory Relay Voltage is too low
code error ENG 341 All data written during powerdown cycle was lost (checksum error)
code error ENG 343 Engine Controller Failure - Hardware Failure
code error ENG 349 Measured Speed is too high.
code error ENG 352 5 Volt Sensor Supply voltage is too low
code error ENG 378 Front Fueling current is too low
code error ENG 379 Front fueling current is too high
code error ENG 381 Error detected in cold start relay 1
code error ENG 382 Error detected in cold start relay 2
code error ENG 385 5 Volt Sensor Supply voltage is too high
code error ENG 386 5 Volt Sensor Supply voltage is too high
code error ENG 387 Decelerator or Hand Throttle (STD cab) 5 Volt Supply voltage is too high
code error ENG 388 Engine Brake driver 1 circuit failure
code error ENG 392 Engine Brake driver 2 circuit failure
code error ENG 393 Engine Brake driver 3 circuit failure
code error ENG 394 Front Timing current is too low.
code error ENG 395 Front Timing current is too high.
code error ENG 396 Rear Fueling current is too low
code error ENG 397 Rear Fueling current is too high
code error ENG 398 Rear Timing current is too low
code error ENG 399 Rear Timing current is too high
code error ENG 412 J1708 data link cannot transmit
code error ENG 414 J1708 data link not fast enough
code error ENG 415 Oil Pressure level has fallen below the very low warning limit.
code error ENG 418 Water in Fuel sensor indicates the water in the fuel filter needs to be drained.
code error ENG 419 Boost Pressure data invalid
code error ENG 422 Engine Coolant Level Sensor (optional) is failed or the jumper plug is missing
code error ENG 426 J1939 data link cannot transmit
code error ENG 427 J1939 data link not fast enough
code error ENG 428 Water in Fuel Sensor voltage is too high.
code error ENG 429 Water in Fuel Sensor voltage is too low.
code error ENG 431 Hand Throttle (STD cab) Idle Validation Switches are both closed
code error ENG 432 Hand Throttle (STD cab) position potentiometer and switches disagree.
code error ENG 433 Boost Pressure level disagrees with engine operation conditions (speed & power)
code error ENG 434 Unswitched 12 volt supply voltage disconnected without normal key off sequence.
code error ENG 435 Oil Pressure data invalid
code error ENG 441 Battery Voltage is too Low (less than 6 volts)
code error ENG 442 Battery Voltage is too High
code error ENG 443 Decelerator or Hand Throttle (STD cab) 5 Volt Supply voltage is too low
code error ENG 444 Low voltage detected at OEM 5 volt supply
code error ENG 449 Fuel Pressure level has exceeded the warning limit.
code error ENG 451 Fuel Pressure Sensor voltage is too high
code error ENG 452 Fuel Pressure Sensor voltage is too low
code error ENG 456 Fuel Pressure in pump is not changing with operating conditions.
code error ENG 465 Wastegate 1 voltage is too high
code error ENG 466 Wastegate 1 voltage is too low
code error ENG 482 Fuel Pressure Sensor voltage low
code error ENG 483 Rear Bank Post Actuactor Pressure voltage high
code error ENG 484 Rear Bank Post Actuactor Pressure voltage low
code error ENG 485 Rear Fueling actuator overfueling
code error ENG 486 Rear Fueling actuator underfueling
code error ENG 488 Intake Manifold Temperature level has exceeded the warning limit.
code error ENG 489 Measured Speed Sensor data low
code error ENG 491 Wastegate 2 voltage is too high
code error ENG 492 Wastegate 2 voltage is too low
code error ENG 493 The Injection Control Identifier Circuit in the harness has failed.

code error code error TRANS 11 Master Clutch Potentiometer Open Circuit or short to ground

code error TRANS 12 Master Clutch Potentiometer Short to +12 Volts or short to 5 Vreff

code error TRANS 24 None of the code error TRANSmission clutches are calibrated

code error TRANS 37 BOC switch open circuit or Neutral relay stuck open

code error TRANS 38 Shuttled to reverse when no wheel speed signal was available

code error TRANS 47 Clutch pedal bottom of clutch switch misadjusted

code error TRANS 48 BOC switch or Neutral relay short circuit

code error TRANS 49 Auto Guidance Isolation valve driver Fault

code error TRANS 50 Park Brake is powered off when in park

code error TRANS 51 FNRP pod indicates Forward or Reverse is on, when Park is on

code error TRANS 52 Park Brake is stuck on when commanded off

code error TRANS 53 5 volt reference voltage too high

code error TRANS 54 5 volt reference voltage too low

code error TRANS 59 FNRP pod in illogical state (two positions on at same time)

code error TRANS 60 FNRP pod in illogical state (in no position)

code error TRANS 61 System pressure valve solenoid circuit is open circuit or shorted to ground

code error TRANS 62 System pressure solenoid is shorted to B+

code error TRANS 64 code error TRANSmission output Sped is too high (above 8200 RPM)

code error TRANS 65 Operator attempted a shuttle operation while out of the seat

code error TRANS 66 FNRP Pod Forward switch is shorted to ground or open circuit

code error TRANS 67 FNRP Pod Forward switch is shorted to power

code error TRANS 68 FNRP Pod Reverse switch is shorted to ground or open circuit

code error TRANS 69 FNRP Pod Reverse switch is shorted to power

code error TRANS 70 Battery voltage is too low for clutch solenoid operation

code error TRANS 72 code error TRANSmission Oil Temperature is above 122 deg. C

code error TRANS 73 Software is out of the calibration mode and the park brake request is still active.

code error TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration.

code error TRANS 75 Engine speed from code error INST Controller does not mcode error ATCh the speed signal from the alternator.

code error TRANS 76 Engine speed from Eninge Controller does not mcode error ATCh the speed signal from the alternator.

code error TRANS 77 No signal from wheel speed sensor

code error TRANS 78 code error TRANSmission regulated pressure accumulator is discharged

code error TRANS 79 Engine RPM from the alternator is measured too high

code error TRANS 80 Wheel speed sensor is measured too high

code error TRANS 81 code error TRANSmission clutches are slipping

code error TRANS 82 Creep Clutch is not calibrated

code error TRANS 83 Communications Lost with Engine Controller

code error TRANS 103 Odd clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 104 Even clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 105 C1-2 clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 106 C3-4 clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 107 C5-6 clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 108 Master clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 109 Low range clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 110 Mid range clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 111 High range clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 112 Reverse clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 113 Creeper clutch solenoid or its wiring failed open or shorted to ground

code error TRANS 114 Even clutch solenoid coil or its wiring shorted to power

code error TRANS 115 Odd clutch solenoid coil or its wiring shorted to power

code error TRANS 116 C1-2 clutch solenoid coil or its wiring shorted to power

code error TRANS 117 C3-4 clutch solenoid coil or its wiring shorted to power

code error TRANS 118 C5-6 clutch solenoid coil or its wiring shorted to power

code error TRANS 119 Master clutch solenoid coil or its wiring shorted to power

code error TRANS 120 Low range clutch solenoid coil or its wiring shorted to power

code error TRANS 121 Mid range clutch solenoid coil or its wiring shorted to power

code error TRANS 122 High range clutch solenoid coil or its wiring shorted to power

code error TRANS 123 Reverse clutch solenoid coil or its wiring shorted to power

code error TRANS 124 Creeper clutch solenoid coil or its wiring shorted to power

code error TRANS 125 Odd clutch is not calibrated

code error TRANS 126 Even clutch is not calibrated

code error TRANS 127 C1-2 clutch is not calibrated

code error TRANS 128 C3-4 clutch is not calibrated

code error TRANS 129 C5-6 clutch is not calibrated

code error TRANS 130 Low range clutch is not calibrated

code error TRANS 131 Mid range clutch is not calibrated

code error TRANS 132 High range clutch is not calibrated

code error TRANS 133 Reverse clutch is not calibrated

code error TRANS 134 Master clutch is not calibrated

code error TRANS 135 Communication lost with the code error ARMrest controller

code error TRANS 136 Communication lost with the code error INSTrumentation controller

code error TRANS 137 Front Suspension raise lock solenoid circuit shorted or open circuit

code error TRANS 138 Front Suspension raise solenoid circuit shorted or open circuit

code error TRANS 139 Front Suspension lower lock solenoid circuit shorted or open circuit

code error TRANS 140 Front suspension position is above the expected absolute limit

code error TRANS 141 Front suspension position is below the expected absolute limit

code error TRANS 142 Front suspension travel range has not been calibrated

code error TRANS 143 Front suspension position is above the upper suspension range

code error TRANS 144 Front suspension position is below the lower suspension range

code error TRANS 145 Front Suspension lower lock solenoid circuit shorted or open circuit

code error TRANS 146 Regulated system pressure low (below 100PSI / 689 KPA)

code error TRANS 147 Regulated system pressure below 290 PSI

code error TRANS 148 Backup alcode error ARM circuit shorted or open

code error TRANS 150 Front suspension pressure sensor rod side (DA-R) out of range high

code error TRANS 151 Front suspension pressure sensor rod side open circuit

code error TRANS 152 Front Suspension pressure control not able to increase pressure on the rod side

code error TRANS 153 Front Suspension pressure control not able to decrease pressure on the rod side

code error TRANS 154 Front Suspension Lock Valve Stuck on fault (suspension will not lock)

code error TRANS 155 Front Suspension Lock Valve is stuck of (suspension will not unlock)

code error TRANS 156 Lock valve was code error INSTalled but removed

code error ARM 19 Hand THROTTLE potentiometer is failed

code error ARM 29 Aux 1st remote valve LEVER potentiometer is failed

code error ARM 39 Aux 2nd remote valve LEVER potentiometer is failed

code error ARM 49 Aux 3rd remote valve LEVER potentiometer is failed

code error ARM 59 Aux 4th remote valve LEVER potentiometer is failed

code error ARM 69 code error Hitch POSITION command potentiometer is failed

code error ARM 79 code error Hitch LOAD command potentiometer is failed

code error ARM 89 Aux 1st remote valve FLOW potentiometer is failed

code error ARM 99 Aux 2nd remote valve FLOW potentiometer is failed

code error ARM 109 Aux 3rd remote valve FLOW potentiometer is failed

code error ARM 119 Aux 4th remote valve FLOW potentiometer is failed

code error ARM 129 Aux 5th remote valve FLOW potentiometer is failed

code error ARM 139 Aux remote valve TIMER potentiometer is failed

code error ARM 149 code error Hitch UPPER LIMIT potentiometer is failed

code error code error ARM 159 code error Hitch DROP RATE potentiometer is failed

code error ARM 169 code error Hitch TRAVEL potentiometer is failed

code error ARM 1029 Aux 5th remote valve control switch is failed

code error ARM 1039 PTO switch is failed

code error ARM 1049 code error Hitch UP/DOWN switch is failed

code error ARM 1059 code error Hitch SLIP switch is failed

code error ARM 1069 MFD switch is failed

code error ARM 1079 DIFF LOCK switch is failed

code error ARM 1089 Programmable UP/DOWN switch is failed.

code error ARM 1099 Aux remote valve LIMIT SET switch is failed

code error ARM 1109 Hand Throttle IDLE VALIDATION switch is failed

code error ARM 1119 RECORD/PLAY switch is failed

code error ARM 1129 Invalid Configuration - Implement Depth Control switch is failed

code error ARM 1139 Engine Brake switch is failed

code error ARM 1149 Auto Field / code error TRANSport Switch is in an illogical state

code error ARM 8011 Battery Voltage is too Low

code error ARM 9011 Controller Memory Error - Loss of code error Hitch Position Command Calibration

code error ARM 9012 Controller Memory Error - Loss of Aux Remote Lever Calibrations

code error ARM 9013 Controller Memory Error - Loss of Throttle Calibrations

code error ARM 9014 Controller Memory Error - Loss of MFD switch Configuration

code error ARM 9015 Controller Memory Error - Loss of code error TRANS switches Configuration

code error ARM 9021 code error Hitch position command potentiometer calibration results not acceptable

code error ARM 9031 Hand throttle potentiometer calibration results not acceptable

code error ARM 9041 code error Hitch DROP RATE potentiometer calibration value(s) are out of range

code error ARM 10091 code error ARMrest Controller failure - 5 V regulator failure

code error ARM 12013 Communications Lost with Data Bus and ALL other controllers

code error ARM 12081 Loss of/unavailable Performance Monitor Display - RECORD/PLAY functionality disabled

code error TMF 3 code error Hitch Raise Solenoid High Side Driver shorted to 12 volts.

code error TMF 4 code error Hitch Raise Solenoid Failed Open or Shorted to Ground.

code error TMF 5 code error Hitch Lower Solenoid Shorted to 12 volts.

code error TMF 6 code error Hitch Lower Solenoid High Side Driver circuit short to 12 volts.

code error TMF 7 code error Hitch Raise/Lower Solenoids Open or short to ground.

code error TMF 11 Communications Lost with Data Bus and ALL other controllers

code error TMF 12 Communication lost with the code error ARMrest controller

code error TMF 14 5 Volt Sensor Supply voltage is too high

code error TMF 15 5 Volt Sensor Supply voltage is too low

code error TMF 17 code error Hitch Position Command potentiometer failed in the code error ARMrest controller

code error TMF 18 code error Hitch Rockshaft Position potentiometer is outside normal operating range.

code error TMF 19 code error Hitch Upper Limit potentiometer is failed in the code error ARMrest Controller

code error TMF 21 code error Hitch Load Command potentiometer is failed in the code error ARMrest Controller

code error TMF 22 Single draft pin sensor failed when configured for one draft pin sensor.

code error TMF 23 Two draft pin sensors failed when configured for two draft pins.

code error TMF 24 Communications Lost with code error INSTrumentation Controller

code error TMF 25 code error Hitch Up/Down Switch failed in the code error ARMrest controller

code error TMF 26 Fender UP and DOWN switch failure or both switches simultaneously pressed

code error TMF 28 code error Hitch Travel potentiometer is failed in the code error ARMrest Controller

code error TMF 29 code error Hitch Drop Rate potentiometer is failed in the code error ARMrest Controller

code error TMF 30 Right Draft Pin voltage is outside the normal operating range.

code error TMF 31 Left Draft Pin voltage is outside the normal operating range.

code error TMF 32 Ground Speed Signal is failed in the code error INSTrumentation Controller

code error TMF 33 code error Hitch Slip Set Switch failed in the code error ARMrest controller

code error TMF 34 code error Hitch Slip Select Switch failed in the code error ARMrest controller

code error TMF 35 Slip Sensor (radar or wheel speed) is failed in the code error INSTrumentation Controller

code error TMF 37 The ARU reports EDC code error TRANSport Lock is faulty or not available.

code error TMF 41 Draft pin(s) detected but the code error ARMrest controller specified tractor without draft control.

code error TMF 42 Engine speed must be set above 1600 rpm during calibration of lower valve.

code error TMF 43 No Draft pin(s) detected but the code error ARMrest controller specified tractor with draft control.

code error TMF 44 code error Hitch calibration aborted due to tractor movement.

code error TMF 45 code error Hitch calibration attempted when the engine is not running or engine speed signal is failed.

code error TMF 47 Raise Valve calibration value is too high. (valve problem)

code error TMF 48 Raise Valve calibration value is too low. (valve problem)

code error TMF 50 code error Hitch position at top of travel is not within specification during calibration

code error TMF 51 Lower Valve calibration value is too high. (valve problem)

code error TMF 52 Lower Valve calibration value is too low. (valve problem)

code error TMF 53 The time allowed for code error Hitch calibration has expired

code error TMF 54 code error Hitch position at bottom of travel is not within specification during calibration

code error TMF 55 code error Hitch position range from top to bottom is not within spec during calibration

code error TMF 56 code error Hitch position range to position command range ratio is not within spec during calibration.

code error TMF 57 Right Draft Pin voltage is not within spec for ïno loadÍ condition during calibration

code error TMF 58 Left Draft Pin voltage is not within spec for ïno loadÍ condition during calibration

code error TMF 59 Both Draft Pin voltages are not within spec for ïno loadÍ condition during calibration

code error TMF 60 Draft pin connected to left vs right for single pin setup during calibration

code error TMF 61 The code error Hitch Calibration procedure must be performed.

code error TMF 62 Communications Lost with Performance Monitor Function

code error TMF 63 Controller 8 volt reference is too high (above 8.8 volts).

code error TMF 64 Controller 8 volt reference is too low (below 7.2 volts).

code error TMF 65 Battery Voltage is too Low

code error TMF 66 Battery Voltage is too Low

code error TMF 80 MFD fault condition in software.

code error TMF 81 MFD Solenoid is failed Open or Short Circuit

code error TMF 82 Differential Lock Solenoid is failed Open or Short Circuit

code error TMF 83 Brake Lamp Relay Solenoid is failed Open or Short Circuit

code error TMF 86 Wheel Slip Signal is failed in the code error INSTrumentation Controller

code error TMF 87 Ground Speed Signal is failed in the code error INSTrumentation Controller

code error TMF 88 Differential Lock Switch is failed in the code error ARMrest Controller

code error TMF 89 Differential Lock Switch is failed in the code error ARMrest Controller

code error TMF 90 Differential Lock Switch is failed in the code error ARMrest Controller

code error TMF 92 MFD Switch is failed in the code error ARMrest Controller

code error TMF 93 MFD Switch is failed in the code error ARMrest Controller

code error TMF 94 Differential Lockout fault condition in software.

code error TMF 95 The steering angle sensor is above the expected operating range

code error TMF 96 The steering angle sensor is below the expected operating range

code error TMF 98 Battery Voltage is too Low

code error TMF 99 Battery Voltage is too Low

code error TMF 106 Aux 5th remote valve control switch (Extend) is failed in the code error ARMrest Controller

code error TMF 107 Aux 5th remote valve control switch (Retract) is failed in the code error ARMrest Controller

code error TMF 108 Aux 1st remote valve LEVER potentiometer is failed in the code error ARMrest Controller

code error TMF 109 Aux 2nd remote valve LEVER potentiometer is failed in the code error ARMrest Controller

code error TMF 110 Aux 3rd remote valve LEVER potentiometer is failed in the code error ARMrest Controller

code error TMF 111 Aux 4th remote valve LEVER potentiometer is failed in the code error ARMrest Controller

code error TMF 112 Aux 1st remote valve FLOW potentiometer is failed in the code error ARMrest Controller

code error TMF 113 Aux 2nd remote valve FLOW potentiometer is failed in the code error ARMrest Controller

code error TMF 114 Aux 3rd remote valve FLOW potentiometer is failed in the code error ARMrest Controller

code error TMF 115 Aux 4th remote valve FLOW potentiometer is failed in the code error ARMrest Controller

code error TMF 116 Aux 5th remote valve FLOW potentiometer is failed in the code error ARMrest Controller

code error TMF 120 Electro Hydraulic Remote top link switch is stuck on.

code error TMF 123 Aux 1st Lower Coil solenoid shorted to 12 volts.

code error TMF 124 Aux 1st Lower solenoid failed open or short circuit.

code error TMF 125 Aux 1st Raise Coil solenoid shorted to 12 volts.

code error TMF 126 Aux 1st Raise solenoid failed open or short circuit.

code error TMF 127 Aux 2nd Lower Coil solenoid shorted to 12 volts.

code error TMF 128 Aux 2nd Lower solenoid failed open or short circuit.

code error TMF 129 Aux 2nd Raise Coil solenoid shorted to 12 volts.

code error TMF 130 Aux 2nd Raise solenoid failed open or short circuit.

code error TMF 131 Aux 3rd Lower Coil solenoid shorted to 12 volts.

code error TMF 132 Aux 3rd Lower solenoid failed open or short circuit.

code error TMF 133 Aux 3rd Raise Coil solenoid shorted to 12 volts.

code error TMF 134 Aux 3rd Raise solenoid failed open or short circuit.

code error TMF 135 Aux 4th Lower Coil solenoid shorted to 12 volts.

code error TMF 136 Aux 4th Lower solenoid failed open or short circuit.

code error TMF 137 Aux 4th Raise Coil solenoid shorted to 12 volts.

code error TMF 138 Aux 4th Raise solenoid failed open or short circuit.

code error TMF 139 Aux 5th Lower Coil solenoid shorted to 12 volts.

code error TMF 141 Aux 5th Raise Coil solenoid shorted to 12 volts.

code error TMF 142 Aux 5th Raise solenoid failed open or short circuit.

code error TMF 147 Implement feedback #1 out of range High

code error TMF 148 Implement feedback #1 out of range Low

code error TMF 149 Implement feedback #2 out of range High

code error TMF 150 Implement feedback #2 out of range Low

code error TMF 151 Communications Lost with code error TRANSmission Controller

code error TMF 152 Electro Hydraulic Remote top link switch voltage is short circuit.

code error TMF 153 Electro Hydraulic Remote top link switch data invalid

code error TMF 154 PTO switch interlock - Cab Switch and Fender switch on at the same time.

code error TMF 155 Auto PTO switch data failed in the code error ARMrest controller.

code error TMF 156 Auto PTO switch stuck ON in code error ARMrest Controller.

code error TMF 157 PTO remote fender switch short circuit.

code error TMF 158 PTO remote fender switch open circuit

code error TMF 159 PTO remote fender switch stuck ON.

code error TMF 160 PTO Clutch is Slipping Too Much

code error TMF 162 Engine Stalled when the PTO was running.

code error TMF 163 PTO Shaft rotation is detected when the PTO clutch is OFF.

code error TMF 164 PTO shaft speed has not been detected within 3.6 seconds of being turned ON.

code error TMF 165 PTO Shaft rotation is detected when the Engine is OFF.

code error TMF 166 PTO Driver is on and no current is sensed.

code error TMF 167 Current sensed when the PTO driver is off.

code error TMF 168 PTO ON/OFF switch is failed in the code error ARMrest Controller

code error TMF 169 PTO ON/OFF switch is failed in the code error ARMrest Controller

code error TMF 170 PTO ON/OFF switch is failed in the code error ARMrest Controller

code error TMF 171 PTO software fault condition detected.

code error TMF 172 PTO Solenoid Circuit is failed shorted to 12 Volts when PTO is in the off state.

code error TMF 173 PTO Solenoid Circuit is failed shorted to ground when PTO is in the off state.

code error TMF 174 Current flowing in the PTO sense resistor when the high side is off.

code error TMF 175 PTO Clutch has not reached lock up speed within 6 seconds of being turned ON

code error TMF 178 PTO speed sensor has been changed.

code error TMF 179 The PTO is receiving no frequency from the Shaft Size Sensor on a two speed PTO

code error TMF 180 The PTO is receiving signals from the Shaft Size Sensor on a single speed PTO configuration.

code error INST 1015 Seat Switch may be stuck closed.

code error INST 1024 code error TRANS oil filter switch shorted to ground on power up.

code error INST 1034 Hydraulic oil filter switch shorted to ground on power up.

code error INST 3010 PTO Shaft Speed sensor is failed in PTO Controller

code error INST 3020 Engine Speed sensor is failed in the Engine Controller

code error INST 3022 Engine Overspeed Error

code error INST 5010 Engine Oil Pressure sensor is failed in the Engine Controller

code error INST 5011 Engine Oil Pressure sensor voltage is too low (open circuit, short to ground)

code error INST 7024 Reversible Fan Control open circuit or shorted to ground.

code error INST 10031 Controller Memory Error - Loss of Engine Hours information

code error INST 10032 Controller Memory Error - Loss of Vehicle Configuration information

code error INST 10033 Controller Memory Error - Loss of Customer Configuration information

code error INST 10034 Controller Memory Error: Loss of valid fuel table information.

code error INST 10035 Controller Memory Error - Loss of Valid Radar Configuration information.

code error INST 10036 Controller Memory Error - Loss of Displayed Performance information

code error INST 10037 Controller Memory Error - Loss of Implement Width information

code error INST 10038 Controller Memory Error - Loss of Valid Remote Timer information.

code error INST 11011 Fuel Level Sensor voltage is too low (open circuit, short to ground)

code error INST 12011 Communications Lost with code error ARMrest Controller

code error INST 12021 Communications Lost with Auxiliary Controller

code error INST 12031 Communications Lost with code error Hitch Controller

code error INST 12043 Communications Lost with Data Bus 1 and ALL other controllers

code error INST 12051 Communications Lost with PTO Controller

code error INST 12053 Communications Lost with Vehicle Data Bus 2.

code error INST 12071 Communications Lost with code error TRANSmission Controller

code error INST 12091 Communications Lost with Engine Controller

code error INST 12101 Communications Lost with Tractor ECU (Gateway) Controller

code error INST 12111 Communications Lost with Automatic Temperature Controller

code error INST 12121 Communications Lost with Color Perfomance Monitor

code error INST 13010 Engine Coolant Temperature sensor is failed in the Engine Controller

code error INST 13011 Engine Coolant Temperature sensor voltage is too low (short to ground)

code error INST 13012 Engine Coolant Temperature sensor voltage is too high (open circuit, short to +V)

code error INST 13021 code error TRANSmission Oil Temperature sensor voltage is too low (short to ground)

code error INST 13022 code error TRANSmission Oil Temperature sensor voltage is too high (open circuit, short to +V)

code error INST 13031 Hydraulic Oil Temperature sensor voltage is too low (short to ground)

code error INST 13032 Hydraulic Oil Temperature sensor voltage is too high (open circuit, short to +V)

code error INST 13040 Air to Air Intake Temperature sensor is failed in the Engine Controller

code error INST 13044 When fuel shut off relay is lcode error ATChed, short is detected (mechanical engine tractors only)

code error INST 13051 Air to Air Intake Temperature sensor voltage is too low (short to ground)

code error INST 13052 Air to Air Intake Temperature sensor voltage is too high (open circuit, short to +V)

code error INST 53001 code error INSTrumentation Controller Configuration is Incorrect

code error INST 53002 Air to Air Intake sensor does not mcode error ATCh Tractor Model Configuration

code error INST 53005 Engine Shutdown activated by code error INSTrument Controller

code error INST 65535 NO ERROR. Errors have not been cleared from factory.

code error ATC 111 Cab sensor open or shorted to power

code error ATC 112 Cab sensor shorted to ground

code error ATC 115 Evaporator sensor open or shorted to power

code error ATC 116 Evaporator sensor shorted to ground

code error ATC 120 Blower speed select pot open/shorted to power

code error ATC 121 Temperature select pot open/shorted to power

code error ATC 122 Mode Select Pot Open Or Shorted To Power

code error ATC 125 High pressure switch (+) input shorted to power

code error ATC 126 High pressure switch (+) input shorted to ground

code error ATC 127 High pressure switch (-) input shorted to power

code error ATC 128 High pressure switch (-) input shorted to ground

code error ATC 129 High pressure cycling error (2 in 1 minute)

code error ATC 130 Low pressure switch (+) input shorted to power

code error ATC 131 Low pressure switch (+) input shorted to ground

code error ATC 132 Low pressure switch (-) input shorted to power

code error ATC 133 Low pressure switch (-) input shorted to ground

code error ATC 134 Low pressure switch open for > 1 minute

code error ATC 113 Outlet sensor open or shorted to power

code error ATC 114 Outlet sensor shorted to ground

code error ATC 117 Outside air sensor open or shorted to power

code error ATC 118 Outside air sensor shorted to ground

code error code error Hitch 1002 Raise code error Hitch valve coil short to 12 volts or raise code error Hitch valve coil circuit failure.

code error Hitch 1003 Open or Short to Ground raise code error Hitch valve coil circuit failure.

code error Hitch 1004 Lower code error Hitch valve coil short to 12 volts or lower code error Hitch valve coil circuit failure.

code error Hitch 1005 Open or short to ground lower code error Hitch valve coils.

code error Hitch 1006 EDC Low Side Driver stuck on failure.

code error Hitch 1007 Low side driver wcode error ATChdog test failed.

code error Hitch 1008 Low side of raise solenoid connected permanently to GND

code error Hitch 1009 Low side of lower solenoid connected permanently to GND

code error Hitch 1011 TCU (Tractor Controller Unit) is disconnected from the CAN bus.

code error Hitch 1012 No communication with the ACM (code error ARMrest Controller Module).

code error Hitch 1013 No communication with the ICP (code error INSTrument Cluster Panel).

code error Hitch 1014 Five-volt reference is above the upper voltage limit.

code error Hitch 1015 Five-volt reference is below the lower voltage limit.

code error Hitch 1016 Not implemented

code error Hitch 1017 Position Command value received over the CAN data bus from the code error ARMrest indicates Position Command potentiometer failed.

code error Hitch 1018 code error Hitch rockshaft position potentiometer open/short/misadjust or circuit failure.

code error Hitch 1019 Upper Limit value received from CAN data bus indicates failure condition.

code error Hitch 1021 Load Command value received from CAN data bus indicates failure condition.

code error Hitch 1022 Single draft pin sensor failed when configured for one draft pin sensor.(CCH Only)

code error Hitch 1023 Two draft pin sensors failed when configured for two draft pins.(CCH Only)

code error Hitch 1024 ICU CAN data bus signal lost.

code error Hitch 1025 Up/Down/Down Momentary switch value received from CAN data bus indicates switch failure.

code error Hitch 1026 Up/Down remote fender switch failure.

code error Hitch 1027 Not implemented

code error Hitch 1028 Travel Range potentiometer value received from CAN data bus indicates failure condition.

code error Hitch 1029 Drop Rate value received from CAN data bus indicates potentiometer failure condition.

code error Hitch 1030 Right draft pin voltage is outside the normal operating range.(CCH Only)

code error Hitch 1031 Left draft pin voltage is outside the normal operating range.(CCH Only)

code error Hitch 1032 Ground speed failure-value received from CAN data bus indicates failure condition.

code error Hitch 1033 Slip Limit Set Point received from CAN data bus indicates failure condition.

code error Hitch 1034 Slip Enable switch received from CAN data bus indicates failure condition.

code error Hitch 1035 The Percent slip received from ETC indicates failure condition.

code error Hitch 1036 The ARU reports EDC Inching Up switch faulty or not available.

code error Hitch 1037 The ARU reports EDC Inching Down switch faulty or not available.

code error Hitch 1065 The ARU specified tractor without draft control (position only code error Hitch) but detected presence of draft pin(s).

code error TRANS 2009 Seat switch open circuit

code error TRANS 2010 Seat switch is shorted to the supply voltage B+ or 5 volt reference

code error TRANS 2011 Clutch Pot Open Circuit or short to ground

code error TRANS 2012 Clutch Potentiometer Short to +12 Volts or short to 5 Volt reference.

code error TRANS 2024 none of the code error TRANSmission clutches are calibrated. This will be the condition when a new controller is code error INSTalled on the tractor.

code error TRANS 2037 Bottom of Clutch pedal switch open circuit or bottom of clutch relay is stuck open

code error TRANS 2047 Clutch pedal bottom of clutch switch misadjusted.

code error TRANS 2048 Bottom of Clutch pedal switch or the bottom of clutch relay are short circuit

code error TRANS 2049 code error TRANS

code error TRANS 2054 5 volt reference voltage too low.

code error TRANS 2055 No signal from wheel speed sensor.

code error TRANS 2056 5 volt internal reference voltage too high.

code error TRANS 2057 5 volt internal reference voltage too low.

code error TRANS 2059 1) Switch inputs indicate shuttle lever is in both forward and neutral 2) Switch inputs indicate shuttle lever is in both reverse and neutral3) Switch inputs indicate shuttle lever is in both forward and reverse. Cycle the shuttle lever which may free up stuck switches, or try driving the opposite direction.

code error TRANS 2071 Forward switch input from the FNRP Pod is shorted to ground or is open circuit.

code error TRANS 2072 Reverse switch input from the FNRP Pod is shorted to +12 Volts or the FNRP pod 5 Volt Reference.

code error TRANS 2073 Reverse switch input from the FNRP Pod is shorted to ground or open circuit.

code error TRANS 2074 FNR Not Park Switch low voltage fault

code error TRANS 2075 FNR Not Park Switch high Voltage fault

code error TRANS 2110 FNR Neutral Switch Low Voltage fault

code error TRANS 2111 FNR Neutral Switch high Voltage fault

code error TRANS 2326 The Engine RPM sourced from the alternator measured by the controller is excessively high.

code error TRANS 2327 No engine RPM

code error TRANS 2330 The code error TRANSmission output RPM speed, sourced from the sensor, measured by the controller is too high for the desired gear

code error TRANS 2331 The code error TRANSmission clutches are slipping

code error TRANS 2342 Clutch Odd solenoid open circuit or short to ground.

code error TRANS 2343 Clutch Even solenoid open circuit or short to ground.C33

code error TRANS 2344 Clutch C1-2 solenoid open circuit or short to ground.

code error TRANS 2345 Clutch C3-4 solenoid open circuit or short to ground.

code error TRANS 2346 Clutch 5-6 solenoid open circuit or short to ground.

code error TRANS 2374 Master Clutch solenoid open circuit or short to ground.

code error TRANS 2347 Clutch Low Range solenoid open circuit or short to ground.

code error TRANS 2348 110 Clutch Mid Range solenoid open circuit or short to ground.

code error TRANS 2349 Clutch High Range solenoid open circuit or short to ground.

code error TRANS 2350 Clutch reverse solenoid open circuit or short to ground.

code error TRANS 2351 The creeper clutch solenoid is open circuit or short to ground

code error TRANS 2353 Even Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.

code error TRANS 2352 Odd Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.

code error TRANS 2354 C1-2 Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off..

code error TRANS 2355 C3-4 Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off.

code error TRANS 2356 C5-6 clutch Solenoid is shorted to +12 Volts, current sensed while driver isoff.

code error TRANS 2357 Low clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.

code error TRANS 2358 Mid Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off.

code error TRANS 2359 High Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.

code error TRANS 2360 Reverse Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.

code error TRANS 2361 The creeper clutch solenoid is shorted to +12 Volts, current sensed while the driver is off

code error TRANS 2362 Master Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.

code error TRANS 2363 The Odd Clutch is not calibrated

code error TRANS 2364 Even Clutch not calibrated

code error TRANS 2365 C1-2 Clutch not calibrated

code error TRANS 2366 C3-4 Clutch not calibrated

code error TRANS 2367 C5-6 Clutch not calibrated

code error TRANS 2368 Low Range Clutch not calibrated

code error TRANS 2369 Mid Range Clutch not calibrated

code error TRANS 2370 High Clutch not calibrated

code error TRANS 2371 Reverse Clutch not calibrated

code error TRANS 2372 Creep Clutch is not calibrated

code error TRANS 2373 Master Clutch not calibrated

code error TRANS 2800 Auto Guidance Isolation valve driver Fault

code error TRANS 2805 System pressure valve solenoid circuit is open circuit or shorted to ground

code error TRANS 2806 System pressure solenoid is shorted to B+

code error TRANS 2807 code error TRANSmission output rpm over speed

code error TRANS 2809 The battery voltage is too low to permit operation of the clutch solenoids.

code error TRANS 2811 code error TRANSmission Oil Temperature Hot

code error TRANS 2812 code error TRANSmission Oil Temperature sensor short to B+ or open circuit

code error TRANS 2813 code error TRANSmission oil temperature Sensor Short to Ground

code error TRANS 2814 Integrated Control Panel off line

code error TRANS 2815 Governor Engine RPM alternator engine RPM mismcode error ATCh

code error TRANS 2816 code error TRANSmission regulated pressure accumulator is flat

code error TRANS 2817 Governor is offline CAN bus

code error TRANS 2818 Communication lost with the code error ARMrest Control Module(ACM)

code error TRANS 2819 Communication lost with the code error INSTrumentation controller.

code error TRANS 2820 System pressure low possible System pressure hydraulic pump failure or leak

code error TRANS 2821 System Pressure Low fault

code error TRANS 2850 The Park Brake is stuck on by no electrical power supplied when commanded on

code error TRANS 2851 The Park Brake Driver has detected an over current or an open circuit condition

code error TRANS 2852 The Park Brake is stuck on by no electrical power supplied to the solenoid when driver is commanded on. Possible service brake bottom brake switches open.

code error TRANS 2055 No signal from wheel speed sensor.

code error TRANS 2873 Software is out of the calibration mode and the park brake request is still active. If this fault is detected there is a bug in the software

code error TRANS 2874 The park brakes commanded on and gear is engaged and there is no park brake request from calibration. If this fault is detected there is a bug in the software

code error TRANS 2900 Torque sensor Gap is on the larger end of the tolerance (CCH Only)

code error TRANS 2901 Signal received from the torque sensor is not in any fault range or normal range tolerance (CCH Only)

code error TRANS 2902 Torque sensor has declared an internal fault tolerance (CCH Only)

code error TRANS 2903 Torque sensor supply voltage below 4.8 volts tolerance (CCH Only)

code error TRANS 2910 12VF1voltage supply is low. (possible blown fuse*)

code error TRANS 2911 12VT1voltage supply is low. (possible blown fuse*)

code error TRANS 2912 12VF2voltage supply is low. (possible blown fuse*)

code error TRANS 2913 12VHvoltage supply is low. (possible blown fuse*)

code error TRANS 2914 12VF3voltage supply is low. (possible blown fuse*)

code error TRANS 2915 12VS1voltage supply is low. (possible blown fuse*)
 

 

code error code error Engine 3000 Unknown ECM Error Code Received

code error Engine 3999 Unknown ECM Error Code Received

code error Engine 3001 Foot Throttle Sensor -Signal Not Plausible

code error Engine 3002 Foot Throttle Sensor -Signal Above Range Max.

code error Engine 3003 Foot Throttle Sensor -Signal Below Range Min.

code error Engine 3004 Foot Throttle Sensor -No Signal -Error

code error Engine 3006 Coolant Temperature Sensor -Signal Not Plausible(Compared with code error Engine Oil Temperature)

code error Engine 3007 Coolant Temperature Sensor -Signal Above Range Max.

code error Engine 3008 Coolant Temperature Sensor -Signal Below Range Min.

code error Engine 3009 Coolant Temperature Sensor -(via CAN) No Signal

code error Engine 3010 Air Intake Temperature Sensor -Signal Above Range Max.

code error Engine 3011 Air Intake Temperature Sensor -Signal Above Range Min.

code error Engine 3012 Air Intake Temperature Sensor -(via CAN) No Signal

code error Engine 3015 Fuel Temperature Signal -Signal Above Range Max.

code error Engine 3016 Fuel Temperature Signal -Signal Below Range Min.

code error Engine 3019 Boost Pressure Sensor -Signal Above Range Max.

code error Engine 3021 Boost Pressure Sensor -(via CAN) No Signal

code error Engine 3022 Boost Pressure Sensor -Signal Not Plausible

code error Engine 3023 Atmospheric Pressure Sensor -Signal Not Plausible Compared with Boost Pressure

code error Engine 3024 Atmospheric Pressure Sensor -Signal Above Range Max.

code error Engine 3025 Atmospheric Pressure Sensor -Signal Below Range Min.

code error Engine 3028 Oil Pressure Too Low

code error Engine 3029 Oil Pressure Sensor _Short circuit to Battery

code error Engine 3030 Oil Pressure Sensor _Short circuit to Ground

code error Engine 3031 Oil Pressure Sensor -Hardware Error

code error Engine 3032 Oil Pressure Sensor -Value Too High

code error Engine 3033 Oil Temperature Sensor -Signal Not Plausible (Compared with Coolant Temperature)

code error Engine 3034 Oil Temperature Sensor -Signal Above Range Max.

code error Engine 3035 Oil Temperature Sensor -Signal Below Range Min.

code error Engine 3036 Oil Temperature Sensor -(via CAN) No Signal

code error Engine 3037 Boost Pressure Sensor -Signal Low

code error Engine 3038 Constant code error Engine RPM Activate / Select Switch _Short circuit to Ground

code error Engine 3039 Cruise Control Actuating Device -Evaluation Error

code error Engine 3043 Vehicle Speed Sensing -Hardware Conversion Error

code error Engine 3044 Vehicle Speed Sensing -Signal Above Range Max.

code error Engine 3045 Vehicle Speed Sensing -Signal Below Range Min.

code error Engine 3046 Vehicle Speed Sensing -Signal Not Plausible

code error Engine 3047 Main Relay 2 Failure _Short circuit to Battery

code error Engine 3048 Main Relay 2 Failure _Short circuit to Ground

code error Engine 3051 Battery Voltage to ECM too High

code error Engine 3052 Battery Voltage to ECM too Low

code error Engine 3053 Vehicle Speed Sensing (Tacho) -PWM Frequency Too High

code error Engine 3054 Vehicle Speed Sensing (Tacho) -PWM Average Frequency Above Limit

code error Engine 3055 Vehicle Speed Sensing (Tacho) -PWM Average Frequency Below Limit

code error Engine 3056 Vehicle Speed Sensing (Tacho) -Not Plausible

code error Engine 3057 Timeout of CAN Message High Resolution Wheel Speed

code error Engine 3058 Timeout of CAN Message Vehicle Dynamics Control Unit

code error Engine 3059 ECM After run was Interrupted

code error Engine 3060 Cylinder1 -Unclassifiable Error in Injector

code error Engine 3061 Cylinder1 -Injector Cable Short circuit (Low Side to Battery)

code error Engine 3062 Cylinder1 -Application Dependent

code error Engine 3063 Cylinder1 -Injector Cable Short circuit (High Side to Ground)

code error Engine 3064 Cylinder5 -Unclassifiable Error in Injector

code error Engine 3065 Cylinder5 -Injector Cable Short circuit (Low Side to Battery)

code error Engine 3066 Cylinder5 -Application Dependent

code error Engine 3067 Cylinder5 -Injector Cable Short circuit (High Side to Ground)

code error Engine 3068 Cylinder3 -Unclassifiable Error in Injector

code error Engine 3069 Cylinder3 -Injector Cable Short circuit (Low Side to Battery)

code error Engine 3070 Cylinder3 -Application Dependent

code error Engine 3071 Cylinder3 -Injector Cable Short circuit (High Side to Ground)

code error Engine 3072 Cylinder6 -Unclassifiable Error in Injector

code error Engine 3073 Cylinder6 -Injector Cable Short circuit (Low Side to Battery)

code error Engine 3074 Cylinder6 -Application Dependent

code error Engine 3075 Cylinder6 -Injector Cable Short circuit (High Side to Ground)

code error Engine 3076 Cylinder2 -Unclassifiable Error in Injector

code error Engine 3077 Cylinder2 -Injector Cable Short circuit (Low Side to Battery)

code error Engine 3078 Cylinder2 -Application Dependent

code error Engine 3079 Cylinder2 -Injector Cable Short circuit (High Side to Ground)

code error Engine 3080 Cylinder4 -Unclassifiable Error in Injector

code error Engine 3081 Cylinder4 -Injector Cable Short circuit (Low Side to Battery)

code error Engine 3082 Cylinder4 -Application Dependent

code error Engine 3083 Cylinder4 -Injector Cable Short circuit (High Side to Ground)

code error Engine 3088 Crankshaft Sensor -No Signal

code error Engine 3089 Crankshaft Sensor -Invalid Signal

code error Engine 3090 Camshaft Sensor -No Signal

code error Engine 3091 Camshaft Sensor -Invalid Signal

code error Engine 3092 Offset Between Camshaft and Crankshaft -Not Plausible

code error Engine 3093 Offset Between Camshaft and Crankshaft -Outside Boundaries

code error Engine 3095 Operating with Camshaft Sensor Only -Backup Mode

code error Engine 3096 Tier 3: ECM Bus Off on CAN A Tier 4a: ECM Bus Off on Vehicle CAN

code error Engine 3097 ECM Bus Off on code error Engine private CAN

code error Engine 3098 Timeout of CAN Message TSC1-TE (When Active)

code error Engine 3099 Timeout of CAN Message TSC1-TE (When Inactive)

code error Engine 3100 Timeout of CAN Message TSC1-AE (When Active)

code error Engine 3101 Timeout of CAN Message TSC1-AE (When Inactive)

code error Engine 3102 Rail Pressure Sensor CP3 -Signal Below Range Min.

code error Engine 3104 Rail Pressure Relief Valve -Open

code error Engine 3105 Rail Pressure Relief Valve -Pressure Shock Requested

code error Engine 3106 Rail Pressure Relief Valve -Did Not Open After Pressure Shock

code error Engine 3107 Metering Unit _Short circuit to Battery

code error Engine 3108 Metering Unit _Short circuit to Ground

code error Engine 3110 Rail Pressure Sensor Offset Monitoring -Value above Limit

code error Engine 3111 Rail Pressure Sensor Offset Monitoring -Value below Limit

code error Engine 3112 Rail Pressure Sensor CP3 -Signal Above Range Max.

code error Engine 3113 Main Relay 1 (High Pressure Pump -power supply to the fuel metering unit) -Short to Battery

code error Engine 3114 Main Relay 1 (High Pressure Pump -power supply to the fuel metering unit) Short to Ground

code error Engine 3117 PTO Twist Sensor -Out of Range

code error Engine 3118 ECM 12V Sensor Supply Voltage High

code error Engine 3119 ECM 12V Sensor Supply Voltage Low

code error Engine 3120 PTO Twist Sensor -Not Plausible

code error Engine 3121 PTO Twist Sensor -Open Circuit

code error Engine 3122 PTO Twist Sensor _Short circuit to Ground

code error Engine 3123 PTO Twist Sensor -Not Calibrated

code error Engine 3124 Hand Throttle -Channel 2 Above Range Max.

code error Engine 3125 Hand Throttle -Channel 2 Below Range Min.

code error Engine 3126 Hand Throttle -Channel 1 Signal Above Range Max.

code error Engine 3127 Hand Throttle -Channel 1 Signal Below Range Min.

code error Engine 3128 Hand Throttle -Channel Difference Error

code error Engine 3129 Hand Throttle -Idle Switch Closed Circuit

code error Engine 3130 Hand Throttle -Idle Switch Open Circuit

code error Engine 3131 Grid Heater Always Switched On

code error Engine 3133 Cold Start Lamp -No Load

code error Engine 3134 Cold Start Lamp _Short circuit to Battery

code error Engine 3135 Cold Start Lamp _Short circuit to Ground

code error Engine 3136 Cold Start Lamp -Excessive Temperature

code error Engine 3137 Metering Unit -Open Load

code error Engine 3138 Metering Unit -Temperature Too High

code error Engine 3139 Metering Unit Signal Range Check -Signal Too High

code error Engine 3140 Metering Unit Signal Range Check -Signal Too Low

code error Engine 3141 Fuel Flow Set point Too Low

code error Engine 3142 High Pressure Test -Test Active

code error Engine 3143 Grid Heater Switch Off Test (Voltage Drop Too High)

code error Engine 3144 Grid Heater Switch Off Test (Voltage Drop Too Low)

code error Engine 3145 Terminal 15 -No Signal

code error Engine 3146 Water Detected In Fuel

code error Engine 3147 Oil Temperature Too High

code error Engine 3148 Coolant Temperature Sensor Dynamic Test -Failure (Minimum Temperature Raise Not Reached)

code error Engine 3149 Coolant Temperature Sensor Test -Failure (Minimum Temperature Not Reached)

code error Engine 3150 System/Amber Warning Lamp _Short circuit to Battery

code error Engine 3151 System/Amber Warning Lamp _Short circuit to Ground

code error Engine 3152 System/Amber Warning Lamp -No Load

code error Engine 3153 System/Amber Warning Lamp -Excessive Temperature

code error Engine 3154 Grid Heater Relay _Short circuit to Battery

code error Engine 3155 Grid Heater Relay _Short circuit to Ground

code error Engine 3156 Grid Heater Relay -No Load

code error Engine 3157 ECM Not Detected on CAN bus

code error Engine 3158 Invalid ECM Checksum

code error Engine 3159 Invalid code error Engine Reference Torque

code error Engine 3160 Fan Actuator _Short circuit to Battery

code error Engine 3161 Fan Actuator _Short circuit to Ground

code error Engine 3162 Fan Actuator -Open Load

code error Engine 3163 Fan Actuator -Temperature Too High

code error Engine 3164 Fan Speed Sensor _Signal High

code error Engine 3165 Fan Speed Sensor -Signal Low

code error Engine 3166 Fuel Filter Heater Relay _Short circuit to Battery

code error Engine 3167 Fuel Filter Heater Relay _Short circuit to Ground

code error Engine 3168 Fuel Filter Heater Relay -Open Load

code error Engine 3169 Fuel Filter Heater Relay -Signal Not Plausible

code error Engine 3176 Set point of Metering Unit Not Plausible in Overrun

code error Engine 3177 code error Engine Over speed Detected

code error Engine 3178 Timeout of CAN Message BC2EDC1

code error Engine 3179 Timeout of CAN Message BC2EDC2

code error Engine 3180 Timeout of CAN Message VCM2EDC

code error Engine 3181 Rail Pressure Positive Deviation Too High Concerning Set point

code error Engine 3182 Timeout of CAN Message RxCCVS

code error Engine 3183 Timeout of CAN Message TSC1-VR (When Active)

code error Engine 3184 Timeout of CAN Message TSC1-VR (When Inactive)

code error Engine 3185 Timeout of CAN message TF

code error Engine 3186 Cylinder1 Warning -Fast Decay Error

code error Engine 3187 Cylinder1 Warning -Application Dependent

code error Engine 3188 Cylinder1 Warning -Injector Circuit Low

code error Engine 3189 Cylinder1 Warning -Current Level Error

code error Engine 3190 Cylinder2 Warning -Fast Decay Error

code error Engine 3191 Cylinder2Warning -Application Dependent

code error Engine 3192 Cylinder2 Warning -Open Load

code error Engine 3193 Cylinder2 Warning -Current Level Error

code error Engine 3194 Cylinder3 Warning -Fast Decay Error

code error Engine 3195 Cylinder3 Warning -Application Dependent

code error Engine 3196 Cylinder3 Warning -Open Load

code error Engine 3197 Cylinder3 Warning -Current Level Error

code error Engine 3198 Cylinder4 Warning -Fast Decay Error

code error Engine 3199 Cylinder4 Warning -Application Dependent

code error Engine 3200 Cylinder4 Warning -Open Load

code error Engine 3201 Cylinder4 Warning -Current Level Error

code error Engine 3202 Cylinder5 Warning -Fast Decay Error

code error Engine 3203 Cylinder5 Warning -Application Dependent

code error Engine 3204 Cylinder5 Warning -Open Load

code error Engine 3205 Cylinder5 Warning -Current Level Error

code error Engine 3206 Cylinder6 Warning -Fast Decay Error

code error Engine 3207 Cylinder6 Warning -Application Dependent

code error Engine 3208 Cylinder6 Warning -Open Load

code error Engine 3209 Cylinder6 Warning -Current Level Error

code error Engine 3210 Bank1 -General Short circuit on Injection Cable

code error Engine 3211 Bank1 -Injection Cable Short circuit Low Side to Ground

code error Engine 3212 Bank1 -Application Dependent

code error Engine 3213 Bank1 -Unclassifiable Error

code error Engine 3214 Bank1 Warning -Application Dependent

code error Engine 3215 Bank1 Warning -Application Dependent

code error Engine 3216 Bank1 Warning -Open Load

code error Engine 3217 Bank1 Warning -Unclassifiable Error

code error Engine 3218 Bank2-General Short circuit on Injection Cable

code error Engine 3219 Bank2 -Injection Cable Short circuit Low Side to Ground

code error Engine 3220 Bank2 -Application Dependent

code error Engine 3221 Bank2 -Unclassifiable Error

code error Engine 3222 Bank2 Warning -Application Dependent

code error Engine 3223 Bank2 Warning -Application Dependent

code error Engine 3224 Bank2 Warning -Open Load

code error Engine 3225 Bank2 Warning -Unclassifiable Error

code error Engine 3226 Messages SRA2EDC

code error Engine 3227 Injection Processor (CY33X) Error -Internal Reset / Clock Loss / Voltage Too Low

code error Engine 3228 Injection Processor (CY33X) Error -Unlocked / Initialization Failure

code error Engine 3229 Injection Processor (CY33X) Error -Injections Limited By Software

code error Engine 3230 Injection Processor (CY33X) Error -SPI Communication Failure

code error Engine 3231 Injection Processor Error -Internal Reset / Clock Loss / Voltage Too Low

code error Engine 3232 Injection Processor Error -Unlocked / Initialization Failure

code error Engine 3233 Injection Processor Error -Test Mode

code error Engine 3234 Injection Processor Error -SPI Communication Failure

code error Engine 3235 Number of Injections Limited -by Charge Balance

code error Engine 3236 Number of Injections Limited -by Quantity Balance

code error Engine 3237 Number of Injections Limited -by Software

code error Engine 3238 ECM Internal SPI Communication Error -CJ940

code error Engine 3239 ECM EEPROM -Read Operation Failure

code error Engine 3240 ECM EEPROM -Write Operation Failure

code error Engine 3241 ECM EEPROM -Default Value Used

code error Engine 3242 ECM (Locked) Recovery Occurred

code error Engine 3243 ECM (Suppressed) -Recovery Occurred

code error Engine 3244 ECU Recovery (Visible) -Recovery Occurred

code error Engine 3245 ECM Processor -Watchdog Not Plausible

code error Engine 3246 Shutoff Paths During Initialization -Watchdog

code error Engine 3247 Shutoff Paths During Initialization -Supply Voltage Too High

code error Engine 3248 Shutoff Paths During Initialization -Supply Voltage Too Low

code error Engine 3249 TPU Monitoring -Time Deviation between TPU and System Not Plausible

code error Engine 3250 Dataset -Variant Defect

code error Engine 3251 Dataset -Requested Variant Could Not Be Set

code error Engine 3252 Controller Watchdog -SPI Communication Failure

code error Engine 3253 ADC Monitoring -Reference Voltage Too High

code error Engine 3254 ADC Monitoring -Reference Voltage Too Low

code error Engine 3255 ADC Monitoring -Test Impulse Error

code error Engine 3256 ADC Monitoring -Queue Error

code error Engine 3257 Turbine Speed and Air Pressure Too High

code error Engine 3258 High Side Power -Short circuit to Battery

code error Engine 3259 High Side Power _Short circuit to Ground

code error Engine 3260 Low Side Power -Open Load

code error Engine 3261 Low Side Power -Short circuit to Battery of Excess Temperature

code error Engine 3262 Low Side Power _Short circuit to Ground

code error Engine 3263 ECM Bus Off on CAN C

code error Engine 3264 Immobilizer -Injection Disabled

code error Engine 3265 Overrun Monitoring -Injection Time Too Long

code error Engine 3266 Redundant code error Engine Speed in Overrun Monitoring -Speed Signal Not Plausible

code error Engine 3267 Main relay 3 _Short circuit to Battery

code error Engine 3268 Main relay 3 _Short circuit to Ground

code error Engine 3269 Grid Heater Switch On Test -Voltage Drop Too High

code error Engine 3270 Grid Heater Switch On Test -Voltage Drop Too Low

code error Engine 3271 Fuel Low Pressure Sensor -(via CAN) No Signal

code error Engine 3272 Fuel Low Pressure Sensor -Signal Above Range Max.

code error Engine 3273 Fuel Low Pressure Sensor -Signal Below Range Min.

code error Engine 3274 Fuel Low Pressure Sensor Dynamic Plausibility Test -Above Map

code error Engine 3275 Fuel Low Pressure Sensor Dynamic Plausibility Test -Below Map

code error Engine 3276 MIL Visualization Not Available for BC2EDC1

code error Engine 3277 Timeout of CAN Message Dashboard Display

code error Engine 3278 ECM Internal Supply Voltage Too High -CJ940 Above Limit

code error Engine 3279 ECM Internal Supply Voltage Too Low -CJ940 Below Limit

code error Engine 3280 Sensor Supply Voltage 1 -High

code error Engine 3281 Sensor Supply Voltage 1 - Low

code error Engine 3282 Timeout of CAN Message WSI (Wheel Speed Info)

code error Engine 3283 Sensor Supply Voltage 2 -High

code error Engine 3284 Sensor Supply Voltage 2 - Low

code error Engine 3285 Sensor Supply Voltage 3 -High

code error Engine 3286 Sensor Supply Voltage 3 - Low

code error Engine 3287 Turbo Compound Monitoring -No Signal

code error Engine 3288 Turbo Compound Monitoring -Signal High

code error Engine 3289 Turbo Compound Monitoring -Signal Low

code error Engine 3290 Turbo Compound Monitoring -Signal Not Plausible

code error Engine 3291 Cylinder 1 Specific Errors -No Signal

code error Engine 3292 Cylinder 1 Specific Errors -Signal Low

code error Engine 3293 Cylinder 1 BIP Search Failure -Too Many Unsuccessful Searched

code error Engine 3294 Cylinder 1 Specific Errors -Signal Not Plausible

code error Engine 3295 Cylinder 2 Specific Errors -No Signal

code error Engine 3296 Cylinder 2 Specific Errors -Signal Low

code error Engine 3298 Cylinder 2 Specific Errors -Signal Not Plausible

code error Engine 3299 Cylinder 3 Specific Errors -No Signal

code error Engine 3300 Cylinder 3 Specific Errors -Signal Low

code error Engine 3301 Cylinder 3 BIP Search Failure -Too Many Unsuccessful Searches - Rail Pressure Negative Deviation too High on Minimum Metering

code error Engine 3302 Cylinder 3 Specific Errors -Signal Not Plausible

code error Engine 3303 Cylinder 4 Specific Errors -No Signal

code error Engine 3304 Cylinder 4 Specific Errors -Signal Low

code error Engine 3305 Cylinder 4 BIP Search Failure -Too Many Unsuccessful Searches - Rail Pressure below Minimum Limit in Controlled Mode

code error Engine 3306 Cylinder 4 Specific Errors -Signal Not Plausible

code error Engine 3307 Cylinder 5 Specific Errors -No Signal

code error Engine 3308 Cylinder 5 Specific Errors -Signal Low

code error Engine 3309 Cylinder 5 BIP Search Failure -Too Many Unsuccessful Searches - Rail Pressure above Maximum Limit in Controlled Mode

code error Engine 3310 Cylinder 5 Specific Errors -Signal Not Plausible

code error Engine 3311 Cylinder 6 Specific Errors -No Signal

code error Engine 3312 Cylinder 6 Specific Errors -Signal Low

code error Engine 3313 Cylinder 6 BIP Search Failure -Too Many Unsuccessful Searches - Rail Pressure Drop Rate too High

code error Engine 3314 Cylinder 6 Specific Errors -Signal Not Plausible

code error Engine 3315 Minimum Number of Injections Not Reached -Stop code error Engine

code error Engine 3316 Minimum Number of Injections Not Reached -Stop code error Engine

code error Engine 3317 Minimum Number of Injections Not Reached -Stop code error Engine

code error Engine 3318 Minimum Number of Injections Not Reached -Stop code error Engine

code error Engine 3319 DM1code error DCU SPN2 message -Error in code error DCU active

code error Engine 3320 DM1code error DCU SPN3 message -Error in code error DCU active

code error Engine 3321 Timeout of CAN Message DM1code error DCU SPN4

code error Engine 3322 Timeout of CAN Message ERC1DR

code error Engine 3323 Timeout of CAN Message RxAMCONIv (Ambient Conditions)

code error Engine 3324 Timeout of CAN Message EBC1 (Electronic Brake Switch)

code error Engine 3325 Timeout of CAN Message ETC1 (Transmission)

code error Engine 3326 Timeout of CAN Message ETC2 (Transmission)

code error Engine 3327 Timeout of CAN Message TCO1 (Tachograph)

code error Engine 3328 Timeout of CAN Message TSC1-AR (When Inactive)

code error Engine 3329 Timeout of CAN Message TSC1-AR (When Active)

code error Engine 3330 Timeout of CAN Message TSC1-DE (When Inactive)

code error Engine 3331 Timeout of CAN Message TSC1-DE (When Active)

code error Engine 3332 Timeout of CAN Message TSC1-DR (When Inactive)

code error Engine 3333 Timeout of CAN Message TSC1-DR (When Active)

code error Engine 3334 Timeout of CAN message TSC1-PE Torque (When Active)

code error Engine 3335 Timeout of CAN message TSC1-PE Torque (When Inactive)

code error Engine 3336 Timeout of CAN Message TSC1-TR (When Inactive)

code error Engine 3337 Timeout of CAN Message TSC1-TR (When Active)

code error Engine 3338 Timeout of CAN message TSC1-VE Speed (When Inactive)

code error Engine 3339 Timeout of CAN message TSC1-VE Speed (When Active)

code error Engine 3340 Timeout of CAN Message Time Date

code error Engine 3341 Timeout of CAN Message HRVD (High Resolution Vehicle Distance)

code error Engine 3342 Power Stage Air Heater 2 Actuator -No Signal

code error Engine 3343 Power Stage Air Heater 2 Actuator -Signal High

code error Engine 3344 Power Stage Air Heater 2 Actuator -Signal Low

code error Engine 3345 Total Throttle Failure (Only applies to Dual Throttle Vehicles)

code error Engine 3346 Multiple State Switch

code error Engine 3347 Multiple State Switch

code error Engine 3348 Multiple State Switch

code error Engine 3349 Multiple State Switch

code error Engine 3350 Terminal 50 -Always On

code error Engine 3351 code error Engine Brake Decompression Valve -Open Load

code error Engine 3352 code error Engine Brake Decompression Valve _Short circuit to Battery

code error Engine 3353 code error Engine Brake Decompression Valve _Short circuit to Ground

code error Engine 3354 Main Relay 4 (code error Engine Brake Exhaust Valve) _Short circuit to Ground

code error Engine 3355 Main Relay 4 (code error Engine Brake Exhaust Valve) -Short to Battery or open load

code error Engine 3356 Cylinder Shutoff (Cylinder Balancing Disabled) -Shutoff Active

code error Engine 3357 Misfire in Multiple Cylinders -Too Many Misfires

code error Engine 3358 CAN Transmit Timeout

code error Engine 3359 TSC Demand Physically Implausible

code error Engine 3360 Driving Dynamic Control -Not Plausible

code error Engine 3361 ECM EEPROM -General Error

code error Engine 3362 Torque to Quantity Map -Not Plausible

code error Engine 3363 Atmospheric Pressure Sensor -Processed via ADC (no CAN Plausibility Performed)

code error Engine 3364 Foot Pedal 2 -Signal Too High

code error Engine 3365 Foot Pedal 2 -Signal Too Low

code error Engine 3366 Foot Pedal 2 -Signal Not Plausible Compared to Foot Pedal 1

code error Engine 3367 Coolant Temperature Test Failure

code error Engine 3368 Info: Torque Limitation due to OBD Performance Limiter by Legislation

code error Engine 3369 Torque Reduction due to Smoke Limitation

code error Engine 3370 Info: Torque Limitation due to code error Engine Protection (against Excessive Torque, code error Engine Over speed and Overheat)

code error Engine 3371 Info: Torque Limitation due to Fuel Quantity Limitation because of Injection System Errors

code error Engine 3372 Injection Quantity Adjustment failure -Invalid Adjustment Value

code error Engine 3373 Injection Quantity Adjustment failure -EEPROM Adjustment Value Not Readable

code error Engine 3374 Injection Quantity Adjustment failure -Invalid EEPROM Adjustment Value Checksum

code error Engine 3375 Constant code error Engine RPM Increase / Decrease Switch _Short circuit to Battery

code error Engine 3376 code error Engine Controller Software Does Not Support Power Management (code error Engine Power Management Option Enabled, but code error Engine Software Not Compatible)

code error Engine 3377 Constant code error Engine RPM Switch Detected but Option Not Enabled.

code error Engine 3380 code error Engine Fan Increase Speed Error (open or short circuit)

code error Engine 3381 code error Engine Fan Decrease Speed Error (open or short circuit)

code error Engine 3382 Fan Control Solenoid Short To 12Vr

code error Engine 3383 Fan Control Solenoid Open Or Short To GND

code error Engine 3384 Vistronic code error Engine Cooling Fan driver open or short circuit

code error Engine 3399 code error Engine Fuel Lift Pump relay driver over current fault

code error Engine 3513 SCR Catalyst not present _Relation of temperature behavior between both Catalyst Temperatures not plausible

code error Engine 3517 Ambient Air Temperature Sensor failure (of Humidity Sensor) -Signal too high

code error Engine 3518 Ambient Air Temperature Sensor failure (of Humidity Sensor) -Signal too low

code error Engine 3519 Ambient Air Temperature Sensor failure (of Humidity Sensor) -CAN Signal failure

code error Engine 3521 NOx Estimation failure -Estimated Nox signal not reliable

code error Engine 3528 NOx Sensor Plausibility failure -Signal not plausible

code error Engine 3529 NOx Sensor Failure -Open Load

code error Engine 3530 NOx Sensor Failure -Short Circuit

code error Engine 3532 NOx Sensor Failure -Sensor not ready in time

code error Engine 3533 CAN Message timeout Nox (from Nox Sensor) -CAN timeout

code error Engine 3537 CAN Message timeout DM1code error DCU (from code error DCU) -CAN timeout

code error Engine 3541 CAN Message timeout SCR1 (from code error DCU) -CAN timeout

code error Engine 3545 Info: SCR Dosing Valve Overheat Protection -Torque Limitation Level2 for SCR Protection active

code error Engine 3546 Info: SCR Dosing Valve Overheat Protection -Torque Limitation Level1 for SCR Protection active

code error Engine 3549 Humidity Sensor Signal Ratio failure -Signal Ratio above Limit

code error Engine 3550 Humidity Sensor Signal Ratio failure -Signal Ratio below Limit

code error Engine 3555 CAN Message timeout SCR2 (from code error DCU)-CAN timeout

code error Engine 3557 Info: Humidity Sensor possibly saturated with water droplets -Signal Ratio above Limit

code error Engine 3558 Info: Humidity Sensor possibly saturated with water droplets -Signal Ratio below Limit

code error Engine 3561 NOx value not plausible (After treatment plausibility)

code error Engine 3565 Urea quality and urea warning level 1

code error Engine 3569 urea quality and urea warning level 2

code error Engine 3573 urea quality and urea warning level 3

code error Engine 3577 DM1code error DCU SPN1 message -Error in code error DCU active

code error Engine 3581 Performance limit active due to either stage -Performance Limitation active

code error EHR 4135 Rear Remote No.3 -Spool Deflection Excessive

code error EHR 4136 Rear Remote No.3 -Open Center Position Not Reached

code error EHR 4137 Rear Remote No.3 -Manual Operation

code error EHR 4138 Rear Remote No.3 -Output Stage Faulty

code error EHR 4139 Rear Remote No.3 -Position Transducer Faulty

code error EHR 4140 Rear Remote No.3 -Spool Cannot be Brought Back to Neutral

code error EHR 4141 Rear Remote No.3 -Spool Not in Neutral When Switched On

code error EHR 4142 Rear Remote No.4 -No code error EHR Control Messages

code error EHR 4143 Rear Remote No.4 -Implausible code error EHR Control Messages

code error EHR 4144 Rear Remote No.4 -Checksum Verification Failure

code error EHR 4145 Rear Remote No.4 -Neutral Set point

code error EHR 4146 Rear Remote No.4 -Under Voltage

code error EHR 4147 Rear Remote No.4 -Over Voltage

code error EHR 4148 Rear Remote No.4 -Spool Deflection Too Short

code error EHR 4149 Rear Remote No.4 -Spool Deflection Excessive

code error EHR 4150 Rear Remote No.4 -Open Center Position Not Reached

code error EHR 4151 Rear Remote No.4 -Manual Operation

code error code error EHR 4152 Rear Remote No.4 -Output Stage Faulty

code error EHR 4153 Rear Remote No.4 -Position Transducer Faulty

code error EHR 4154 Rear Remote No.4 -Spool Cannot be Brought Back to Neutral

code error EHR 4155 Rear Remote No.4 -Spool Not in Neutral When Switched On

code error EHR 4156 Rear Remote No.5 -No code error EHR Control Messages

code error EHR 4157 Rear Remote No.5 -Implausible code error EHR Control Messages

code error EHR 4158 Rear Remote No.5 -Checksum Verification Failure

code error EHR 4159 Rear Remote No.5 -Neutral Set point

code error EHR 4160 Rear Remote No.5 -Under Voltage

code error EHR 4161 Rear Remote No.5 _Over Voltage

code error EHR 4162 Rear Remote No.5 -Spool Deflection Too Short

code error EHR 4163 Rear Remote No.5 -Spool Deflection Excessive

code error EHR 4164 Rear Remote No.5 -Open Center Position Not Reached

code error EHR 4165 Rear Remote No.5 -Manual Operation

code error EHR 4166 Rear Remote No.5 -Output Stage Faulty

code error EHR 4167 Rear Remote No.5 -Position Transducer Faulty

code error EHR 4168 Rear Remote No.5 -Spool Cannot be Brought Back to Neutral

code error EHR 4169 Rear Remote No.5 -Spool Not in Neutral When Switched On

code error EHR 4170 Rear Remote No.1 _Lever Not Calibrated

code error EHR 4173 Rear Remote No.2 -Lever Not Calibrated

code error EHR 4177 Rear Remote No.3 -Lever Not Calibrated

code error EHR 4180 Rear Remote No.4 -Lever Not Calibrated

code error EHR 4190 code error EHR 1 Offline Err

code error EHR 4191 code error EHR 2 Offline Err

code error EHR 4192 code error EHR 3 Offline Err

code error EHR 4193 code error EHR 4 Offline Err

code error EHR 4198 code error EHR 5 Offline Err

code error EHR 4216 Rear Remote No.1 -Valve Spool Not Calibrated

code error EHR 4217 Rear Remote No.2 -Valve Spool Not Calibrated

code error EHR 4218 Rear Remote No.3 -Valve Spool Not Calibrated

code error EHR 4219 Rear Remote No.4 -Valve Spool Not Calibrated

code error EHR 4220 Rear Remote No.5 -Valve Spool Not Calibrated

code error EHR 4301 Rear Remote No.6 -No code error EHR Control Messages

code error EHR 4302 Rear Remote No.6 -Implausible code error EHR Control Messages

code error EHR 4303 Rear Remote No.6 -Checksum Verification Failure

code error EHR 4304 Rear Remote No.6 -Neutral Set point

code error EHR 4305 Rear Remote No.6 -Under Voltage

code error EHR 4306 Rear Remote No.6 -Over Voltage

code error EHR 4307 Rear Remote No.6 -Spool Deflection Too Short

code error EHR 4308 Rear Remote No.6 -Spool Deflection Excessive

code error EHR 4309 Rear Remote No.6 -Open Center Position Not Reached

code error EHR 4310 Rear Remote No.6 -Manual Operation

code error EHR 4311 Rear Remote No.6 -Output Stage Faulty

code error EHR 4312 Rear Remote No.6 -Position Transducer Faulty

code error EHR 4313 Rear Remote No.6 -Spool Cannot be Brought Back to Neutral

code error EHR 4314 Rear Remote No.6 -Spool Not in Neutral When Switched On

code error EHR 4315 Rear Remote No.7 -No code error EHR Control Messages

code error EHR 4316 Rear Remote No.7 -Implausible code error EHR Control Messages

code error EHR 4317 Rear Remote No.7 -Checksum Verification Failure

code error EHR 4318 Rear Remote No.7 -Neutral Set point

code error EHR 4319 Rear Remote No.7 -Under Voltage

code error EHR 4320 Rear Remote No.7 -Over Voltage

code error EHR 4321 Rear Remote No.7 -Spool Deflection Too Short

code error EHR 4322 Rear Remote No.7 -Spool Deflection Excessive

code error EHR 4323 Rear Remote No.7 -Open Center Position Not Reached

code error EHR 4324 Rear Remote No.7 -Manual Operation

code error EHR 4325 Rear Remote No.7 -Output Stage Faulty

code error EHR 4326 Rear Remote No.7 -Position Transducer Faulty

code error EHR 4327 Rear Remote No.7 -Spool Cannot be Brought Back to Neutral

code error EHR 4328 Rear Remote No.7 -Spool Not in Neutral When Switched On

code error EHR 4329 Rear Remote No.8 -No code error EHR Control Messages

code error EHR 4330 Rear Remote No.8 -Implausible code error EHR Control Messages

code error EHR 4331 Rear Remote No.8 -Checksum Verification Failure

code error EHR 4332 Rear Remote No.8 -Neutral Set point

code error EHR 4333 Rear Remote No.8 -Under Voltage

code error EHR 4334 Rear Remote No.8 -Over Voltage

code error EHR 4335 Rear Remote No.8 -Spool Deflection Too Short

code error EHR 4336 Rear Remote No.8 -Spool Deflection Excessive

code error EHR 4337 Rear Remote No.8 -Open Center Position Not Reached

code error EHR 4338 Rear Remote No.8 -Manual Operation

code error EHR 4339 Rear Remote No.8 -Output Stage Faulty

code error EHR 4330 Rear Remote No.8 -Position Transducer Faulty

code error EHR 4341 Rear Remote No.8 -Spool Cannot be Brought Back to Neutral

code error EHR 4342 Rear Remote No.8 -Spool Not in Neutral When Switched On

code error EHR 4343 Rear Remote No.5 -Lever Not Calibrated

code error EHR 4344 Rear Remote No.6 -Lever Not Calibrated

code error EHR 4345 Rear Remote No.7 -Lever Not Calibrated

code error EHR 4346 Rear Remote No.8 -Lever Not Calibrated

code error EHR 4347 code error EHR 6 Offline Err

code error EHR 4348 code error EHR 7 Offline Err

code error EHR 4349 code error EHR 8 Offline Err

code error EHR 4350 Rear Remote No.6 -Valve Spool Not Calibrated

code error EHR 4351 Rear Remote No.7 -Valve Spool Not Calibrated

code error EHR 4352 Rear Remote No.8 -Valve Spool Not Calibrated

code error EHR 4353 code error EHR FB 1High Err

code error EHR 4354 code error EHR FB 1 Low Err

code error EHR 4355 code error EHR FB 3 High Err

code error EHR 4356 code error EHR FB 3 Low Err

code error EHR 4357 code error EHR Implement Lower Error

code error EHR 4358 code error EHR Implement Raise Error

code error Rear PTO 5001 PTO cab switch, or Auto PTO switch, or PTO remote fender switch is on during tractor power up.

code error Rear PTO 5002 PTO switch interlock

code error Rear PTO 5003 Auto PTO switch data is set to the error state(CCH Only)

code error Rear PTO 5004 Auto PTO switch stuck on condition(CCH Only)

code error Rear PTO 5005 PTO remote fender switch short(CCH Only)

code error Rear PTO 5006 PTO remote fender switch open(CCH Only)

code error Rear PTO 5007 PTO remote fender switch stuck on(CCH Only)

code error Rear PTO 5008 Both PTO On and Off switches are simultaneously on. One of the PTO switches is short to 12 volts.

code error Rear PTO 5009 PTO solenoid open circuit or shorted to ground or AD12vs2 voltage is low.

code error Rear PTO 5010 PTO solenoid circuit shorted to B+ when PTO is in the off state.

code error Rear PTO 5011 Driver is on and no current is sensed.

code error Rear PTO 5012 PTO clutch is slipping excessively for the duration of 5 seconds or longer.

code error Rear PTO 5013 code error Engine speed is too low for the PTO to be in the ïonÍ state.

code error Rear PTO 5014 PTO is commanded off but the PTO speed greater than zero.

code error Rear PTO 5015 The software has not detected PTO shaft speed for greater than 3 seconds since the PTO initial fill vale was commanded

code error Rear PTO 5016 PTO speed is detected when the PTO is in the off state without code error Engine RPM.

code error Rear PTO 5017 PTO clutch did not lock up after 6 seconds of clutch motion.

code error code error Rear PTO 5018 PTO speed sensors wiring swapped (CCH Only)

code error Rear PTO 5019 PTO is configured as a two speed and no shaft size frequency was detected when the PTO was switched on. (CCH Only)

code error Rear PTO 5020 PTO is configured as a single speed and the shaft size frequency was detected when the PTO was switched on. Shaft size frequency input is only used for two speeds PTO.(CCH Only)

code error Rear PTO 5021 Auto PTO disabled(CCH Only)

code error Rear PTO 5022 PTO switch is in the on position when the code error Engine is off.

code error Rear PTO 5023 PTO clutch lube solenoid circuit shorted to B+ when PTO is in the off state.(4WD Only)

code error Rear PTO 5024 PTO clutch lube solenoid open circuit or shorted to ground or +12 VF3 voltage is low.(4WD Only)

code error Rear PTO 5025 Rear PTO

code error Rear PTO 5027 Low side of PTO solenoid connected permanently to GND

code error Rear PTO 5028 Clutch speed sensor open or short to Vbat

code error Rear PTO 5029 Clutch speed sensor short to GND

code error Rear PTO 5030 Shaft size speed sensor open or short to Vbat(CCH Only)

code error Rear PTO 5031 Shaft size speed sensor short to GND(CCH Only)

code error Rear PTO 5032 12VF3voltage supply is low. (possible blown fuse*)

MFD/Diff Lock 6001 MFD (CCH) or Front Diff Lock (4WD) solenoid failed. Possible Failure modes: 1. Solenoid coil failed 2. Damaged wiring 3. Loose connector or bent pin 4. TCU Internal failure

MFD/Diff Lock 6002 Rear Diff Lock solenoid failed. Possible Failure modes: 1. Diff Lock solenoid coil failed 2. Damaged wiring 3. Loose connector or bent pin 4. TCU Internal failure

MFD/Diff Lock 6003 Brake light relay fault. 1. Short to 12 volts 2. Open circuit or short to ground.

MFD/Diff Lock 6004 CAN-BUS indicating Rear Diff Lock Switch failed in the code error Front Armrest. Possible failure modes: 1. Rear Diff Lock Switch failed in code error Front Armrest2. Auto Diff Lock Switch failed in code error Front Armrest (CCH Only) 3. Communication problems between the TCU controller and the code error Front Armrest controller

MFD/Diff Lock 6005 Rear Differential Lock and Auto Differential Lock (Only CCH):1. Diff Lock On and Auto Diff Lock switches are both active

MFD/Diff Lock 6006 CAN-BUS indicating MFD (CCH) or Front Diff Lock (4WD)Switch failed in the code error Front Armrest. Possible failure modes: 1. MFD (CCH) or Front Diff Lock (4WD)failed in code error Front Armrest2. Auto MFD Switch failed in code error Front Armrest, (CCH). 3. Communication problems between the TCU controller and the code error Front Armrest

MFD/Diff Lock 6007 Both MFD and Auto MFD switches active fault

MFD/Diff Lock 6008 Steering angle sensor above maximum voltage limit.

MFD/Diff Lock 6009 Steering angle sensor below minimum voltage limit.

MFD/Diff Lock 6010 12VS1voltage supply is low. (possible blown fuse*)

MFD/Diff Lock 6011 12VS2 voltage supply is low. (possible blown fuse*)

Front PTO 8001 Front PTO cab switch is on during tractor power up.

Front PTO 8002 Front PTO cab switch open

Front PTO 8003 Front PTO cab switch short

Front PTO 8004 Front PTO solenoid open circuit or shorted to ground or AD12VU2 voltage is low.

Front PTO 8005 Front PTO solenoid circuit shorted to B+ when Front PTO is in the off state.

Front PTO 8006 Low side driver is stuck on and no current is sensed.

Front PTO 8007 Front PTO switch is in the on position when the code error Engine is off.

Front PTO 8010 12VU2voltage supply is low. (possible blown fuse*)

code error code error Front Suspension 10001 code error Front Suspension Pump Not tank Valve solenoid is open circuit or shorted to ground

code error Front Suspension 10002 code error Front Suspension rod Side Valve solenoid is open circuit or shorted to ground

code error Front Suspension 10003 code error Front Suspension piston Side Valve solenoid is open circuit or shorted to ground

code error Front Suspension 10004 code error Front Suspension Position sensor out of Range High Error

code error Front Suspension 10005 code error Front Suspension Position sensor out of Range Low Error

code error Front Suspension 10006 code error Front Suspension will not raise error

code error Front Suspension 10007 code error Front Suspension will not Lower error

code error Front Suspension 10008 code error Front Suspension Piston Pressure transducer range high error

code error Front Suspension 10009 code error Front Suspension Piston Pressure transducer range lower error

code error Front Suspension 10010 code error Front Suspension Rod Pressure transducer range high error

code error Front Suspension 10011 code error Front Suspension Rod Pressure transducer range lower error

code error Front Suspension 10012 code error Front Suspension Rod side pressure will not raise error

code error Front Suspension 10013 code error Front Suspension piston side pressure will not raise error

code error Front Suspension 10014 code error Front Suspension Not calibrated error

code error Front Suspension 10015 code error Front Suspension Lock Valve Solenoid is open circuit or is shorted to ground.

code error Front Suspension 10016 FSUS_ENABLE_SW_ERR 10016

code error Front Suspension 10017 FSUS_ENABLE_SW_NA_ERR10017

code error Front Suspension 10018 code error Front Suspension Pump not tank Solenoid over current

code error Front Suspension 10019 code error Front Suspension rod Side Solenoid over current

code error Front Suspension 10020 code error Front Suspension piston Solenoid over current

code error Front Suspension 10021 code error Front Suspension lock out Solenoid over current

code error Front Suspension 10022 12VM voltage supply is low. (possible blown fuse*)

code error Front Suspension 10023 12VF3 voltage supply is low. (possible blown fuse*)

code error Front Suspension 10024 12VF1 voltage supply is low. (possible blown fuse*)

ICU 14002 Trans oil filter switch closed to ground on power up.

ICU 14003 Hyd oil filter switch closed to ground on power up.

ICU 14005 PTO shaft speed data is _ERROR_ or _NOT AVAILABLE_ state from PTO.

ICU 14006 GOV code error Engine speed data is _ERROR_ or _NOT AVAILABLE_ state from GOV.

ICU 14007 code error Engine Over speeding

ICU 14008 code error Engine oil pressure data is _ERROR_ or _NOT AVAILABLE_ state from GOV.

ICU 14009 Loss of valid code error Engine Hours

ICU 14010 PTO controller off line

ICU 14011 Communications Lost with Vehicle Data Bus 1 and ALL other controllers

ICU 14013 TRANSMISSION Off Line

ICU 14014 code error Engine coolant temperature data is _ERROR_ or _NOT AVAILABLE_ state from GOV.

ICU 14015 code error Engine Intake Air Temperature data is _ERROR|| or _NOT AVAILABLE|| state from GOV.

ICU 14016 code error Engine shutdown activated

ICU 14017 Fuel Level Sensor voltage out of range low.

ICU 14018 GOV Off Line

ICU 14019 ATC Off Line

code error Front Armrest 18001 Hand throttle #1 -voltage too low (New Holland Only)

code error Front Armrest 18002 Hand throttle #1 -voltage too high (New Holland Only)

code error Front Armrest 18003 Hand throttle #2 -voltage too low

code error Front Armrest 18004 Hand throttle #2 -voltage too high

code error Front Armrest 18005 code error Engine droop control -voltage too low

code error Front Armrest 18006 code error Engine droop control -voltage too high

code error Front Armrest 18007 Multi-function handle -switch error

code error Front Armrest 18008 Multi-function handle -voltage too low

code error Front Armrest 18009 Multi-function handle -voltage too high

code error Front Armrest 18010 Powershift throttle -voltage too low (Case IH)

code error Front Armrest 18011 Powershift throttle -voltage too high (Case IH)

code error Front Armrest 18012 CVT mode switch error

code error Front Armrest 18013 Multi-function handle -encoder position error

code error Front Armrest 18014 Rear hitch position control potentiometer -voltage too low

code error Front Armrest 18015 Rear hitch position control potentiometer -voltage too high

code error Front Armrest 18016 Rear hitch draft control potentiometer -voltage too low

code error Front Armrest 18017 Rear hitch draft control potentiometer -voltage too high

code error Front Armrest 18018 Rear hitch height limit potentiometer -voltage too low

code error Front Armrest 18019 Rear hitch height limit potentiometer -voltage too high

code error Front Armrest 18020 Rear hitch drop rate potentiometer -voltage too low

code error Front Armrest 18021 Rear hitch drop rate potentiometer -voltage too high

code error Front Armrest 18022 Rear hitch sensitivity control potentiometer -voltage too low

code error Front Armrest 18023 Rear hitch sensitivity control potentiometer -voltage too high

code error Front Armrest 18024 code error EHR flow encoder position error

code error Front Armrest 18025 Rear hitch slip control potentiometer -voltage too low

code error Front Armrest 18026 Rear hitch slip control potentiometer -voltage too high

code error Front Armrest 18027 code error EHR 5 lever position -voltage too low (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front code error Front Armrest 18028 code error EHR 5 lever position -voltage too high (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18029 code error EHR 6 lever position -voltage too low (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18030 code error EHR 6 lever position -voltage too high (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18031 Front hitch position / pressure control potentiometer -voltage too high

code error Front Armrest 18032 Front hitch position / pressure control potentiometer -voltage too low

code error Front Armrest 18033 Front hitch position / pressure mix potentiometer -voltage too high

code error Front Armrest 18034 Front hitch position / pressure mix potentiometer -voltage too low

code error Front Armrest 18035 Front hitch position height limit potentiometer -voltage too high

code error Front Armrest 18036 Front hitch position height limit potentiometer -voltage too low

code error Front Armrest 18037 Front hitch height limit enable switch error

code error Front Armrest 18038 Front hitch position drop rate potentiometer -voltage too high

code error Front Armrest 18039 Front hitch position drop rate potentiometer -voltage too low

code error Front Armrest 18040 code error EHR 1 lever position -voltage too low

code error Front Armrest 18041 code error EHR 1 lever position -voltage too high

code error Front Armrest 18042 code error EHR 2 lever position -voltage too low

code error Front Armrest 18043 code error EHR 2 lever position -voltage too high

code error Front Armrest 18044 code error EHR 3 lever position -voltage too low

code error Front Armrest 18045 code error EHR 3 lever position -voltage too high

code error Front Armrest 18046 code error EHR float control switch error

code error Front Armrest 18047 code error EHR 4 lever position -voltage too low

code error Front Armrest 18048 code error EHR 4 lever position -voltage too high

code error Front Armrest 18049 Joystick 1 X-axis position -voltage too low

code error Front Armrest 18050 Joystick 1 X-axis position -voltage too high

code error Front Armrest 18051 Joystick 1 Y-axis position -voltage too low

code error Front Armrest 18052 Joystick 1 Y-axis position -voltage too high

code error Front Armrest 18053 Joystick 1 proportional rocker switch -voltage too low

code error Front Armrest 18054 Joystick 1 proportional rocker switch -voltage too high

code error Front Armrest 18055 Joystick 2 X-axis position -voltage too low (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18056 Joystick 2 X-axis position -voltage too high (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18057 Joystick 2 Y-axis position -voltage too low (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18058 Joystick 2 Y-axis position -voltage too high (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18059 Joystick 2 proportional rocker switch -voltage too low (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18060 Joystick 2 proportional rocker switch -voltage too high (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18061 Reference voltage _short circuit to 0V

code error Front Armrest 18062 Reference voltage _short circuit to 12V

code error Front Armrest 18063 EEPROM fault

code error Front Armrest 18064 MFH communication error

code error Front Armrest 18065 MFH basic assurance test error

code error Front Armrest 18066 code error EHR 1 lever implausibility error

code error Front Armrest 18067 code error EHR 2 lever implausibility error

code error Front Armrest 18068 code error EHR 3 lever implausibility error

code error Front Armrest 18069 code error EHR 4 lever implausibility error

code error Front Armrest 18070 code error EHR 5 lever implausibility error (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18071 code error EHR 6 lever implausibility error (not applicable to CCM/APH _it may indicate incorrect configuration of the ACM)

code error Front Armrest 18072 EDC mouse raise/work switch fault (NH Only)

code error DCU 19001 Battery voltage sensing (electrical) _signal high _P0563 Battery voltage evaluation above upper limit

code error DCU 19002 Battery voltage sensing (electrical) |signal low |P0562 Battery voltage evaluation below lower limit

code error DCU 19010 Temperature sensor after catalyst (electrical) _signal high _P042D Catalyst Temperature Sensor Circuit High

code error DCU 19011 Temperature sensor after catalyst (electrical) |signal low |P042C Catalyst Temperature Sensor Circuit Low

code error DCU 19019 Temperature sensor before catalyst (electrical) _signal high _P0428 Catalyst Temperature Sensor Circuit High

code error DCU 19020 Temperature sensor before catalyst (electrical) |signal low |P0427 Catalyst Temperature Sensor Circuit Low

code error DCU 19037 Sensor supply 2 (5V internal; for UREA pressure sensors) _Supply Voltage too high _P204D Reagent -pressure sensor -short circuit high

code error DCU 19038 Sensor supply 2 (5V internal; for UREA pressure sensors) |Supply voltage too low |P204C Reagent -pressure sensor -short circuit low

code error DCU 19046 UREA pressure sensor in box (electrical) |supply voltage error |P204A Reagent -pressure sensor -open circuit

code error DCU 19047 UREA pressure sensor in box (electrical) _signal high _P204D Reagent -pressure sensor -short circuit high

code error DCU 19048 UREA pressure sensor in box (electrical) |signal low |P204C Reagent -pressure sensor -short circuit low

code error DCU 19055 UREA Temperature sensor in box (electrical) _high signal _P2045 Reagent -temperature sensor of pump module -short circuit high

code error DCU 19056 UREA Temperature sensor in box (electrical) |signal low |P2044 Reagent -temperature sensor of pump module -short circuit low

code error DCU 19064 Voltage supply internal heaters 1 (UB1) electrical |Open circuit to UB1 |P20C5 Pump module - Internal heating -open circuit

code error DCU 19065 Voltage supply internal heaters 1 (UB1) electrical |Short to bat at UB1 with Key 15 off |P20C8 Pump module -Internal heating -short circuit high

code error DCU 19073 Voltage supply 2 -tube heaters (UB2) electrical |Short to bat at UB2 with Key 15 off |P20C4 Reagent -suction tube heating -short circuit high

code error DCU 19074 Voltage supply 2 -tube heaters (UB2) electrical |Open circuit to UB2 |P20C1 Reagent -suction tube heating -open circuit

code error DCU 19075 Voltage supply 2 -tube heaters (UB2) electrical |Short circuit to Ground UB2 |P20C3 Reagent - suction tube heating -short circuit low

code error code error DCU 19082 Voltage supply 3 -Coolant control valve and reverting valve (UB3) electrical |Short to bat at UB3 with Key 15 off |P20A3 Vent valve (Reductant Purge Control Valve) -short circuit high

code error DCU 19083 Voltage supply 3 -Coolant control valve and reverting valve (UB3) electrical |Open circuit to UB3 |P20A0 Vent valve (Reductant Purge Control Valve) -open circuit

code error DCU 19084 Voltage supply 3 -Coolant control valve and reverting valve (UB3) electrical |Short circuit to Ground UB3 |P20A2 Vent valve (Reductant Purge Control Valve) -short circuit low

code error DCU 19091 Monitoring VDD11 voltage -Dosing valve |supply voltage low |P0658 12 Volt supply for dosing module -below lower limit

code error DCU 19092 Monitoring VDD11 voltage-Dosing valve _supply voltage high _P0659 12 Volt supply for dosing module -above upper limit

code error DCU 19100 UREA level sensor (electrical) |supply voltage error |P203E Reductant Level Sensor -Circuit Intermittent/Erratic

code error DCU 19101 UREA level sensor (electrical) _signal high _P203D Reagent -tank level sensor -short circuit high

code error DCU 19102 UREA level sensor (electrical) |signal low |P203C Reagent -tank level sensor -short circuit low

code error DCU 19109 UREA Temperature sensor in Tank (electrical) _signal high _P205D Reagent -tank temperature sensor (temperature of the Reagent -solution in the tank) -short circuit high

code error DCU 19110 UREA Temperature sensor in Tank (electrical) |signal low |P205C Reagent -tank temperature sensor (temperature of the Reagent -solution in the tank) -short circuit low

code error DCU 19145 Dosing Valve (electrical) |short circuit to batt + |P2049 Reductant Injector -circuit high

code error DCU 19146 Dosing Valve (electrical) |short circuit to ground |P2048 Reductant Injector -circuit low

code error DCU 18147 Dosing Valve (electrical) |open load |P2047 Reductant Injector -circuit open

code error DCU 19148 Dosing Valve (electrical) |Dosing valve permanent ñONî (detection via fast decay) |P209B Reagent-dosing nozzle pressure too high

code error DCU 19154 UREA Pump speed |pump motor unplugged |P208B Reagent-pump not delivering

code error DCU 19155 UREA Pump speed _pump motor blocked _P208A Reagent-pump

code error DCU 19156 UREA Pump speed |pump overspeed |P208D Reagent-pump over speed

code error DCU 19157 UREA Pump speed |Hall sensors defect |P208B Reagent-pump not delivering

code error DCU 19163 Cooling control valve short circuit to UBat or open load |short circuit to battery |P20A3 Vent valve (Reductant Purge Control Valve) -short circuit high

code error DCU 19164 Cooling control valve short circuit to UBat or open load |Open load |P20A0 Vent valve (Reductant Purge Control Valve) -open circuit

code error DCU 19172 Cooling control valve short circuit to ground |short circuit to ground |P20A2 Vent valve (Reductant Purge Control Valve) -short circuit low

code error DCU 19181 Reverting valve (4-2way valve?) electrically |Short circuit to battery |P20A3 Vent valve (Reductant Purge Control Valve) -short circuit high

code error DCU 19182 Reverting valve (4-2way valve?) electrically |Short circuit to ground |P20A2 Vent valve (Reductant Purge Control Valve) -short circuit low

code error DCU 19183 Reverting valve (4-2way valve?) electrically |Open load |P20A0 Vent valve (Reductant Purge Control Valve) -open circuit

code error DCU 19262 Tank heating Valve |Short circuit to battery |P20B4 Reagent -tank heating valve -short circuit high

code error DCU 19263 Tank heating Valve |Short circuit to ground |P20B3 Reagent -tank heating valve -short circuit low

code error DCU 19264 Tank heating Valve |Open load |P20B1 Reagent -tank heating valve -open circuit

code error DCU 19289 Temperature after catalyst too low |Downstream catalyst temp -physical (Catalyst heating time failed) |P042B Catalyst Temperature Sensor Circuit Range/Performance

code error DCU 19298 UREA pressure too low at system start |UREA pressure too low at system start |P208B Reagent pump not delivering

code error DCU 19307 UREA pressure too high |Urea pressure not plausible (urea pressure too high) |P204B Reagent -pressure above threshold

code error DCU 19316 UREA Temperature in Pump Module out of range |Urea temperature box -physical (Urea Box Temp NOT OK: outside range) |P2043 Reagent-temperature sensor of pump module out of range

code error DCU 19325 UREA Temperature in Tank out of range |Urea temperature tank -physical (Urea Tank Temp NOT OK: outside range) |P205B Reagent -tank temperature sensor (temperature of the Reagent -solution in the tank) out of range

code error DCU 19334 System frozen and not free in time _Defreezing Mode and Detection Errors (Inlet line defreezing failed) _P20C2 Reagent -suction tube heating -detection mode of heating

code error DCU 19335 System frozen and not free in time |Defreezing Mode and Detection Errors (pressure line defreezing failed) |P20BE Reagent -pressure tube heating -detection mode of heating

code error DCU 19336 System frozen and not free in time |Defreezing Mode and Detection Errors (pressure build-up in detection mode failed)|P20C5 Pump module -Internal heating -open circuit

code error DCU 19337 System frozen and not free in time |Defreezing Mode and Detection Errors (Back-flow line defreezing failed) |P20B9 Reagent -backflow tube heating -open circuit

code error DCU 19343 Coolant control valve mechanically |mechanical defective blocked open |P20A3 Vent valve (Reductant Purge Control Valve) -short circuit high

code error DCU 19344 Coolant control valve mechanically _mechanical defective blocked closed _P20A0 Vent valve (Reductant Purge Control Valve) -open circuit

code error DCU 19352 Reverting valve (4-2way valve?) mechanically |valve does not open |P20A0 Vent valve (Reductant Purge Control Valve) -open circuit

code error DCU 19361 Battery Voltage (actual value) |High battery voltage |P0562 Battery voltage evaluation -below lower limit

code error DCU 19362 Battery Voltage (actual value) _Low battery voltage _P0563 Battery voltage evaluation -above upper limit

code error DCU 19370 UREA pressure too low (in ñcommissioningî status) |Pump motor error during commissioning (pump not delivering) |P208B Reagent-pump not delivering

code error DCU 19379 UREA Temperature too low during commissioning |Temperatures not plausible during commissioning.

code error DCU 19415 Empty UREA Tank _urea tank empty _P203F Reagent -fluid level in tank -too low

code error DCU 19532 Back flow line clogged |P2063 Reagent -dosing valve -short circuit low

code error DCU 19541 Coolant control valve mechanically |Blocked closed |P20A1 Vent valve test plausibility test (startup)

code error DCU 19550 Pressure line blocked |pressure line blocked |P209B Reagent -dosing nozzle -pressure too high

code error DCU 19559 Low UREA level 1 (warning) -UREA level below Limit 1 -P203F Reagent -fluid level in tank -too low

code error DCU 19568 Low UREA level 2 (warning) -UREA level below Limit 2 -P203F Reagent -fluid level in tank -too low

code error DCU 19577 CAN receive frame E2SCR (Dosing, Exh gas flow, Exh gas temp, Error Suppression, Heater, Long Term failure) |SAE J1939 Check for CAN receive signal : (UREA quantity not in range) |P0600

code error DCU 19578 CAN receive frame E2SCR (Dosing, Exh gas flow, Exh gas temp, Error Suppression, Heater, Long Term failure) |SAE J1939 Check for CAN receive signal : (Dosing status not in range) |P0600 Serial Communication Link

code error DCU 19579 CAN receive frame E2SCR (Dosing, Exh gas flow, Exh gas temp, Error Suppression, Heater, Long Term failure) _timeout _P0600 Serial Communication Link

code error DCU 19580 CAN receive frame E2SCR (Dosing, Exh gas flow, Exh gas temp, Error Suppression, Heater, Long Term failure) |too many CAN messages |P0600 Serial Communication Link

code error DCU 19581 CAN receive frame E2SCR (Dosing, Exh gas flow, Exh gas temp, Error Suppression, Heater, Long Term failure) _SAE J1939 Check for CAN receive signal _P0600 Serial Communication Link

code error DCU 19595 CAN receive frame EEC1 (Driver demand, eng speed, eng torque) |SAE J1939 Check for CAN receive signal : (code error Engine torque not in range) |P0600 Serial Communication Link

code error DCU 19596 CAN receive frame EEC1 (Driver demand, eng speed, eng torque) |SAE J1939 Check for CAN receive signal : (code error Engine speed not in range) |P0600 Serial Communication Link

code error DCU 19597 CAN receive frame EEC1 (Driver demand, eng speed, eng torque) _timeout _P0600 Serial Communication Link

code error DCU 19598 CAN receive frame EEC1 (Driver demand, eng speed, eng torque) |too many CAN messages _ ïP0600 Serial Communication Link

code error DCU 19599 CAN receive frame EEC1 (Driver demand, eng speed, eng torque) |SAE J1939 Check for CAN receive signal : (Torque driver demand not in range) |P0600 Serial Communication Link

code error DCU 19604 CAN receive frame ET1 (Oil and Water temp code error Engine) |SAE J1939 Check for CAN receive signal : (Oil temperature not in range) |P0600 Serial Communication Link

code error DCU 19605 CAN receive frame ET1 (Oil and Water temp code error Engine) _timeout _P0600 Serial Communication Link

code error DCU 19606 CAN receive frame ET1 (Oil and Water temp code error Engine) |too many CAN messages |P0600 Serial Communication Link

code error DCU 19607 CAN receive frame ET1 (Oil and Water temp code error Engine) |SAE J1939 Check for CAN receive signal : (Water temperature not in range) |P0600 Serial Communication Link

code error DCU 19649 UREA Tank level error (CAN message or electrical with real sensor) |Level over CAN: SAE J1939 no Signal available Level sensor connected directly: Sensor Supply error |P203A Reagent -tank level sensor -open circuit 

code error DCU 19650 UREA Tank level error (CAN message or electrical with real sensor) _Level over CAN: SAE J1939 Signal Not in Range Level sensor connected directly: SRC high _P203D Reagent -tank level sensor -short circuit high

code error DCU 19651 UREA Tank level error (CAN message or electrical with real sensor) |Level over CAN: SAE J1939 Erroneous Signal Level sensor connected directly: SRC low |P203C Reagent -tank level sensor - short circuit low

code error DCU 19676 Ambient Temperature: SAE J1939 Check for CAN receive signal : (Signal Range Check: Signal not in range / Erroneous Signal / Signal not available) |SAE J1939 Check for CAN receive signal : (Ambient air temperature not in range) |P0600 Serial Communication Link

code error DCU 19677 Ambient Temperature: SAE J1939 Check for CAN receive signal : (Signal Range Check: Signal not in range / Erroneous Signal / Signal not available) _timeout _P0071 Ambient Air Temperature Sensor Range/Performance

code error DCU 19678 Ambient Temperature: SAE J1939 Check for CAN receive signal : (Signal Range Check: Signal notin range / Erroneous Signal / Signal not available) |too many CAN messages |P0071 Ambient Air Temperature Sensor Range/Performance

code error DCU 19679 Ambient Temperature: SAE J1939 Check for CAN receive signal : (Signal Range Check: Signal not in range / Erroneous Signal / Signal not available) |SAE J1939 Check for CAN receive signal : (Barometric pressure not in range) |P0071 Ambient Air Temperature Sensor Range/Performance

code error DCU 19721 EEPROM / Checksum failures |EEPROM write error |P062F Internal Control Module EEPROM Error

code error DCU 19722 EEPROM / Checksum failures |No corresponding variant number error |P062F Internal Control Module EEPROM Error

code error DCU 19723 EEPROM / Checksum failures |EEPROM communication error |P062F Internal Control Module EEPROM Error

code error DCU 19724 EEPROM / Checksum failures _EEPROM Detection error OR A Codierwort error |P062F Internal Control Module EEPROM Error

code error DCU 19725 EEPROM / Checksum failures |Wrong EEPROM size |P062F Internal Control Module EEPROM Error

code error DCU 19730 Ignition ñonî signal K15 |digital input ignition ON not sensed during initialization |P2530 Ignition switch -plausibility error

code error DCU 19739 Main Relay opens too early / too late |main relay shut off too late |P0687 ECM/PCM Power Relay Control Circuit High

code error DCU 19740 Main Relay opens too early / too late |main relay short circuit |P0685 ECM/PCM Power Relay Control Circuit /Open

code error DCU 19741 Main Relay opens too early / too late |main relay open circuit |P0687 ECM/PCM Power Relay Control Circuit High

code error DCU 19742 Main Relay opens too early / too late _main relay shut off too early (before EEPROM update) _ P0685 ECM/PCM Power Relay Control Circuit /Open

code error DCU 19748 Too high UREA Temperature in Pump module or Leakage test failed (Emergency shut off) _over temperature detection (urea temp. in pump module) _P2043 Reagent -temperature sensor of pump module -Out of range

code error DCU 19749 Too high UREA Temperature in Pump module or Leakage test failed (Emergency shut off) |urea leakage detection (static or dynamic) |P202D Dynamic urea leakage test -Leakage detected

code error DCU 19757 Group error path UREA injection control _Error belonging to group UREA Injection control _ P208B Reagent-pump -Not delivering

code error DCU 19766 Group error path Air control _Error belonging to group air control _P20A7 Compressed air regulation valve

code error DCU 19775 Group error path catalyst temperature _Error belonging to group catalyst temperature out of range _P0426 Plausibility of catalyst temperature sensors -Plausibility error (static)

code error DCU 19784 Group error path NOx exceeded _Error belonging to group NOx exceeded active _P2000 Nox Trap Efficiency Below Threshold

code error DCU 19793 Group error path UREA Tank empty _Error belonging to group UREA tank empty active _P203F Reagent -fluid level in tank -Too low

code error DCU 19999 Unknown code error DCU15 fault code

  NEW HOLLAND ERROR CODES

code error NH 1002 Radar disconnected

code error NH 1003 Speed sensor error

code error NH 1004 Speed sensor signal too High

code error NH 1005 Speed sensor signal too High

code error NH 1006 Slip control potentiometer signal too low

code error NH 1007 Slip control potentiometer signal too High

code error NH 1008 Raise / work switch failure

code error NH 1009 Both external switches operated at the same time

code error NH 1010 Height limit potentiometer signal too low

code error NH 1011 Height limit potentiometer signal too high

code error NH 1012 Drop rate potentiometer signal too low

code error NH 1013 Drop rate potentiometer signal too high

code error NH 1014 R/H load sensing pin signal too low

code error NH 1015 R/H load sensing pin signal too high

code error NH 1016 L/H load sensing pin signal too low

code error NH 1017 L/H load sensing pin signal too high

code error NH 1018 Both load sensing pin disconnected

code error NH 1019 Load sensing pin voltage too low

code error NH 1020 Load sensing pin voltage too high

code error NH 1021 Position / draft control potentiometer too low

code error NH 1022 Position / draft control potentiometer too high

code error NH 1023 Control panel disconnected

code error NH 1024 Perform Hydraulic Lift Autocalibration

code error NH 1025 Mouse lift lever potentiometer signal too low

code error NH 1026 Mouse lift lever potentiometer signal too high

code error NH 1027 Maximum Lift arm position potentiometer too low

code error NH 1028 Maximum Lift arm position potentiometer too high

code error NH 1029 Hydraulic Control valve disconnected

code error NH 1030 Ground signal open circuit ( not used )

code error NH 1031 Chassis Harness Disconnected

code error NH 1032 Draft Load potentiometer shorted to +12v

code error NH 1033 Draft Load potentiometer open circuit

code error NH 1049 Wheel speed sensor open circuit

code error NH 1053 5 volt reference Short to +12v

code error NH 1054 5 volt reference Short to ground.

code error NH 1057 Module Failure ( not used )

code error NH 1059 5 volt reference Open circuit ( not used )

code error NH 1063 Lower solenoid open circuit

code error NH 1064 Raise solenoid open circuit

code error NH 1065 lower solenoid short circuit

code error NH 1066 Raise solenoid short circuit

code error NH 1067 EDC Hydraulic Valve supply too low

code error NH 1068 Height limit Calibration Error

code error NH 2001 'N' - Shuttle too fast error

code error NH 2002 Flash N error

code error NH 2003 'CP' - Clutch pedal required

code error NH 2004 'P' - Handbrake error

code error NH 2005 Creeper selection error

code error NH 2011 Clutch Pedal Potentiometer Signal too Low

code error NH 2012 Clutch Pedal Potentiometer Signal too High

code error NH 2013 Up and Down buttons at same time

code error NH 2014 Switch 4 / 5 error ( not used )

code error NH 2015 HI / LO shift lever switches both closed

code error NH 2016 Creeper Solenoid Short circuit

code error NH 2021 Chassis Harness Error

code error NH 2024 Synchro clutches not calibrated

code error NH 2026 Engine speed too high

code error NH 2027 Engine speed too low

code error NH 2035 Dump solenoid circuit fault

code error NH 2036 Dump solenoid open circuit

code error NH 2037 Clutch Pedal switch open circuit

code error NH 2038 Clutch 4 solenoid short circuit

code error NH 2039 Clutch 4 solenoid open circuit

code error NH 2040 Clutch 3 solenoid short circuit

code error NH 2041 Clutch 3 solenoid open circuit

code error NH 2042 Clutch 2 solenoid short circuit

code error NH 2043 Clutch 2 solenoid open circuit

code error NH 2044 Clutch 1 solenoid short circuit

code error NH 2045 Clutch 1 solenoid open circuit

code error NH 2046 Fuse 12 open circuit ( not used )

code error NH 2047 Clutch pedal switch set too High

code error NH 2048 Clutch pedal switch set too Low

code error NH 2049 Wheel speed sensor short or open

code error NH 2051 Oil temperature sensor open circuit

code error NH 2052 Oil temperature sensor short circuit

code error NH 2053 5 Volt Potentiometer Supply too High

code error NH 2054 5 Volt Potentiometer Supply too Low

code error NH 2055 No signal from wheel speed sensor

code error NH 2056 Low Range switch open

code error NH 2057 High Range switch open

code error NH 2058 Seat switch closed for 25 hours

code error NH 2059 Shuttle Lever switch disagree

code error NH 2060 Synchro Fwd no longer engaged

code error NH 2061 F/R Synchro Potentiometer signal too high

code error NH 2062 F/R Synchro Potentiometer signal too low

code error NH 2063 Synchro not moving to forward

code error NH 2064 Synchro not moving to reverse

code error NH 2065 Forward solenoid open circuit

code error NH 2066 Reverse solenoid open circuit

code error NH 2067 Forward solenoid circuit fault

code error NH 2068 Reverse solenoid circuit fault

code error NH 2069 Synchro reverse no longer engaged

code error NH 2070 Voltage with lever in forward too high

code error NH 2071 Voltage with lever in forward too low

code error NH 2072 Voltage with lever in reverse too high

code error NH 2073 Voltage with lever in reverse too low

code error NH 2075 Flywheel Speed Sensor Frequency is too high

code error NH 2075 Any period is too short, under 400 microseconds

code error NH 2075 Any short period is longer than the corresponding long period

code error NH 2075 Damper angle is below 50 degrees or above 85 degrees

code error NH 2075 Calculated torque exceeds calibrated peak torque by more than 25%

code error NH 2075 No usable signals from the flywheel sensor, and ERPM is greater than 300

code error NH 2076 Flywheel Speed Sensor open circuit

code error NH 2077 Flywheel Speed Sensor short circuit

code error NH 2080 Synchro 4 no longer engaged

code error NH 2081 4/5 Synchro Potentiometer signal too high

code error NH 2082 4/5 Synchro Potentiometer signal too low

code error NH 2083 Synchro 4 engaged error

code error NH 2084 Synchro 5 engaged error

code error NH 2085 Synchro 4 solenoid open circuit

code error NH 2086 Synchro 5 solenoid open circuit

code error NH 2087 Synchro 4 solenoid short to 12v

code error NH 2088 Synchro 5 solenoid short to 12v

code error NH 2089 Synchro 5 no longer engaged

code error NH 2090 Output speed too high in creeper

code error NH 2091 C3 Clutch not calibrated

code error NH 2092 C4 Clutch not calibrated

code error NH 2093 High Clutch not calibrated

code error NH 2094 Low Clutch not calibrated

code error NH 2095 C1 Clutch not calibrated

code error NH 2096 C2 Clutch not calibrated

code error NH 2097 Clutch 5 not calibrated

code error NH 2098 C5 solenoid short to 12v

code error NH 2099 C5 open circuit

code error NH 2100 C5 dump solenoid short to 12v

code error NH 2101 C5 dump solenoid open circuit

code error NH 2124 Flywheel Torque Sensor not calibrated

code error NH 2199 Creeper option not enabled

code error NH 3001 Accelerator Pedal Signal - NOT PLAUSIBLE

code error NH 3002 Accelerator Pedal Signal - SOURCE HIGH

code error NH 3003 Accelerator Pedal Signal - SOURCE LOW

code error NH 3004 Accelerator Pedal Signal - NO SIGNAL

code error NH 3005 Accelerator Pedal Signal - ALL OTHER FAULTS

code error NH 3006 Coolant Temperature Signal - ABOVE NORMAL

code error NH 3007 Coolant Temperature Signal - SOURCE HIGH

code error NH 3008 Coolant Temperature Signal - SOURCE LOW

code error NH 3009 Coolant Temperature Signal - NO SIGNAL

code error NH 3010 Air (boost) Temperature Signal - SOURCE HIGH

code error NH 3011 Air (boost) Temperature Signal - SOURCE LOW

code error NH 3012 Air (boost) Temperature Signal - NO SIGNAL

code error NH 3014 Fuel Temperature Signal - ABOVE NORMAL

code error NH 3015 Fuel Temperature Signal - SOURCE HIGH

code error NH 3016 Fuel Temperature Signal - SOURCE LOW

code error NH 3017 Fuel Temperature Signal - NO SIGNAL

code error NH 3018 Boost Pressure Signal - ABOVE NORMAL

code error NH 3019 Boost Pressure Signal - SOURCE HIGH

code error NH 3020 Boost Pressure Signal - SOURCE LOW

code error NH 3021 Boost Pressure Signal - NO SIGNAL

code error NH 3022 Boost Pressure Signal - ALL OTHER FAULTS

code error NH 3023 Atmospheric Pressure Signal - ABOVE NORMAL

code error NH 3024 Atmospheric Pressure Signal - SOURCE HIGH

code error NH 3025 Atmospheric Pressure Signal - SOURCE LOW

code error NH 3026 Atmospheric Pressure Signal - NO SIGNAL

code error NH 3027 Oil Pressure Signal - ABOVE NORMAL

code error NH 3028 Oil Pressure Signal - BELOW NORMAL

code error NH 3029 Oil Pressure Signal - SOURCE HIGH

code error NH 3030 Oil Pressure Signal - SOURCE LOW

code error NH 3031 Oil Pressure Signal - NO SIGNAL

code error NH 3032 Oil Pressure Signal - ALL OTHER FAULTS

code error NH 3033 Oil Temperature Signal - ABOVE NORMAL

code error NH 3034 Oil Temperature Signal - SOURCE HIGH

code error NH 3035 Oil Temperature Signal - SOURCE LOW

code error NH 3036 Oil Temperature Signal - NO SIGNAL

code error NH 3037 Power stage Fuel filter heater - SOURCE HIGH

code error NH 3038 Power stage Fuel filter heater - SOURCE LOW

code error NH 3039 Power stage Fuel filter heater - NO SIGNAL

code error NH 3040 HS Power stage cold start heater relay - SOURCE HIGH

code error NH 3041 HS Power stage cold start heater relay - SOURCE LOW

code error NH 3042 HS Power stage cold start heater relay - NO SIGNAL

code error NH 3043 Adapt.cylinder balancing Cylinder 1 - SOURCE HIGH

code error NH 3044 Adapt.cylinder balancing Cylinder 5 - SOURCE HIGH

code error NH 3045 Adapt.cylinder balancing Cylinder 3 - SOURCE HIGH

code error NH 3046 Adapt.cylinder balancing Cylinder 6 - SOURCE HIGH

code error NH 3047 Adapt.cylinder balancing Cylinder 2 - SOURCE HIGH

code error NH 3048 Adapt.cylinder balancing Cylinder 4 - SOURCE HIGH

code error NH 3049 Battery voltage signal - ABOVE NORMAL

code error NH 3050 Battery voltage signal - BELOW NORMAL

code error NH 3051 Battery voltage signal - SOURCE HIGH

code error NH 3052 Battery voltage signal - SOURCE LOW

code error NH 3053 LS Power stage cold start lamp - SOURCE HIGH

code error NH 3054 LS Power stage cold start lamp - SOURCE LOW

code error NH 3055 LS Power stage cold start lamp - NO SIGNAL

code error NH 3056 Cold start heater monitoring - BELOW NORMAL

code error NH 3057 Cold start heater monitoring - NOT PLAUSIBLE

code error NH 3058 Cold start heater monitoring - SOURCE LOW

code error NH 3059 Cold start heater monitoring - NO SIGNAL

code error NH 3060 Injector solenoid valve Cylinder 1 - NOT PLAUSIBLE

code error NH 3061 Injector solenoid valve Cylinder 1 - SOURCE HIGH

code error NH 3062 Injector solenoid valve Cylinder 1 - SOURCE LOW

code error NH 3063 Injector solenoid valve Cylinder 1 - NO SIGNAL

code error NH 3064 Injector solenoid valve Cylinder 5 - NOT PLAUSIBLE

code error NH 3065 Injector solenoid valve Cylinder 5 - SOURCE HIGH

code error NH 3066 Injector solenoid valve Cylinder 5 - SOURCE LOW

code error NH 3067 Injector solenoid valve Cylinder 5 - NO SIGNAL

code error NH 3068 Injector solenoid valve Cylinder 3 - NOT PLAUSIBLE

code error NH 3069 Injector solenoid valve Cylinder 3 - SOURCE HIGH

code error NH 3070 Injector solenoid valve Cylinder 3 - SOURCE LOW

code error NH 3071 Injector solenoid valve Cylinder 3 - NO SIGNAL

code error NH 3072 Injector solenoid valve Cylinder 6 - NOT PLAUSIBLE

code error NH 3073 Injector solenoid valve Cylinder 6 - SOURCE HIGH

code error NH 3074 Injector solenoid valve Cylinder 6 - SOURCE LOW

code error NH 3075 Injector solenoid valve Cylinder 6 - NO SIGNAL

code error NH 3076 Injector solenoid valve Cylinder 2 - NOT PLAUSIBLE

code error NH 3077 Injector solenoid valve Cylinder 2 - SOURCE HIGH

code error NH 3078 Injector solenoid valve Cylinder 2 - SOURCE LOW

code error NH 3079 Injector solenoid valve Cylinder 2 - NO SIGNAL

code error NH 3080 Injector solenoid valve Cylinder 4 - NOT PLAUSIBLE

code error NH 3081 Injector solenoid valve Cylinder 4 - SOURCE HIGH

code error NH 3082 Injector solenoid valve Cylinder 4 - SOURCE LOW

code error NH 3083 Injector solenoid valve Cylinder 4 - NO SIGNAL

code error NH 3084 Injector Booster Voltage C1 - SOURCE HIGH

code error NH 3085 Injector Booster Voltage C1 - SOURCE LOW

code error NH 3086 Injector Booster Voltage C2 - SOURCE HIGH

code error NH 3087 Injector Booster Voltage C2 - SOURCE LOW

code error NH 3088 Increment speed signal - NOT PLAUSIBLE

code error NH 3089 Increment speed signal - SOURCE LOW

code error NH 3090 Segment speed signal - NOT PLAUSIBLE

code error NH 3091 Segment speed signal - SOURCE LOW

code error NH 3092 Engine Speed Sensing - NOT PLAUSIBLE

code error NH 3093 Engine Speed Sensing - SOURCE HIGH

code error NH 3094 Engine Speed Sensing - SOURCE LOW

code error NH 3095 Engine Speed Sensing - NO SIGNAL

code error NH 3096 CAN (A) Hardware - NO SIGNAL

code error NH 3097 CAN (B) Hardware - NO SIGNAL

code error NH 3098 CAN TSC1_TE Control - SOURCE LOW

code error NH 3099 CAN TSC1_TE Control - NO SIGNAL - CAN TE and CAN AE (Torque Request) error codes may be generated due to normal shutdown timing differences between the ECU and the XCM. If so, the actual error code 3096 or 3097 should also be displayed.

code error NH 3100 CAN TSC1_AE Control - SOURCE LOW

code error NH 3101 CAN TSC1_AE Control - NO SIGNAL

code error NH 3102 Fuel pressure monitoring CP3 - ALL OTHER FAULTS

code error NH 3102 Possible Causes: • Low fuel supply to CP3 (filter restriction). • Low output from CP3 • CP3 PWM fault (Check PWM output in Atlas, min 3% at engine idle, max 24% at full load Above 24% indicates excessive fuel leakage from the overpressure valve in the rail or Injector/transfer tube (remove the fuel return lines to check). 

code error NH 3103 Fuel pressure signal - ABOVE NORMAL

code error NH 3104 Fuel pressure signal - SOURCE HIGH

code error NH 3105 Fuel pressure signal - SOURCE LOW

code error NH 3106 Fuel pressure signal - NO SIGNAL

code error NH 3107 CC HS Power stage 1 fuel press. Control - SOURCE HIGH

code error NH 3108 CC HS Power stage 1 fuel press. Control - SOURCE LOW

code error NH 3109 CC HS Power stage 1 fuel press. Control - NO SIGNAL

code error NH 3110 Monitoring of rail pressure relief valve - ABOVE NORMAL

code error NH 3111 Monitoring of rail pressure relief valve - BELOW NORMAL

code error NH 3112 Rail pressure Min / Max. error - SOURCE HIGH

code error NH 3113 Main relay defect - ABOVE NORMAL

code error NH 3114 Main relay defect - BELOW NORMAL

code error NH 3115 Main relay defect - NOT PLAUSIBLE

code error NH 3116 Main relay defect - SOURCE HIGH

code error NH 3117 ECU: Self Test Shutoff Paths ( Start Up ) - NOT PLAUSIBLE. Engine will derate to 1800 rpm.

code error NH 3117 Possible Causes: • ECU power failed when the engine was running or engine shut down process was incorrect. 

code error NH 3118 Power supply for sensors - NOT PLAUSIBLE

code error NH 3119 Power supply for sensors - NO SIGNAL

code error NH 3120 Power supply for sensors - ALL OTHER FAULTS

code error NH 3121 PTO Torque sensor open circuit

code error NH 3122 PTO Torque sensor short circuit

code error NH 3123 PTO Torque not CAL error

code error NH 3124 Hand Throttle potentiometer 2 high error.

code error NH 3125 Hand Throttle potentiometer 2 Low error.

code error NH 3126 Hand Throttle potentiometer 1 high error.

code error NH 3127 Hand Throttle potentiometer 1 Low error.

code error NH 3128 Hand Throttle potentiometer diff. error.

code error NH 3129 Hand Throttle idle switch high error

code error NH 3130 Hand Throttle idle switch low error

code error NH 3131 ECU self test shutoff paths (start up)

code error NH 3132 CRPM Switch short

code error NH 4001 Signal of Aux-stick (AUX1) out of range low

code error NH 4002 Signal of Aux-stick (AUX1) out of range high

code error NH 4003 Signal from Remote Flow potentiometer 1 (AUX 1) out of range.

code error NH 4005 Signal of Aux-stick (AUX2) out of range low

code error NH 4006 Signal of Aux-stick (AUX2) out of range high

code error NH 4007 Signal from Remote Flow potentiometer 2 (AUX 2) out of range.

code error NH 4008 Signal from Remote valve 2 Timer Pot 1 out of range

code error NH 4009 Signal of Aux-stick (AUX3) out of range low

code error NH 4010 Signal of Aux-stick (AUX3) out of range high

code error NH 4011 Signal from Remote Flow potentiometer 3 (AUX 3) out of range.

code error NH 4015 Signal from Remote Flow potentiometer 4 (AUX 4) out of range.

code error NH 4016 Signal from Remote valve Timer potentiometer 1 out of range.

code error NH 4040 Supply Voltage too low

code error NH 4041 Supply Voltage too High

code error NH 4042 Arm Rest Module (ARU) CAN 'Bus off'.

code error NH 4043 Controller Fault ( Register check)

code error NH 4044 Controller Fault (Flash Memory)

code error NH 4045 Controller Fault (Data Memory)

code error NH 4100 Remote No.1 No control Message Received

code error NH 4101 Remote No.1 Control Message not plausible

code error NH 4102 Remote No.1 EEPROM Error

code error NH 4103 Remote No.1 Switched to failsafe

code error NH 4104 Remote No.1 Under voltage

code error NH 4105 Remote No.1 Over voltage

code error NH 4106 Remote No.1 Spool movement to low

code error NH 4107 Remote No.1 Spool movement to high

code error NH 4108 Remote No.1 Float position not reached

code error NH 4109 Remote No.1 Manually operated

code error NH 4110 Remote No.1 Driver faulty

code error NH 4111 Remote No.1 potentiometer faulty.

code error NH 4112 Remote No.1 Unable to reach neutral

code error NH 4113 Remote No.1 Spool not in neutral at key on

code error NH 4114 Remote No.2 No control Message Received

code error NH 4115 Remote No.2 Control Message not plausible

code error NH 4116 Remote No.2 EEPROM Error

code error NH 4117 Remote No.2 Switched to failsafe

code error NH 4118 Remote No.2 Under voltage

code error NH 4119 Remote No.2 Over voltage

code error NH 4120 Remote No.2 Spool movement to low

code error NH 4121 Remote No.2 Spool movement to high

code error NH 4122 Remote No.2 Float position not reached

code error NH 4123 Remote No.2 Manually operated

code error NH 4124 Remote No.2 Driver faulty

code error NH 4125 Remote No.2 potentiometer faulty

code error NH 4126 Remote No.2 Unable to reach neutral

code error NH 4127 Remote No.2 Spool not in neutral at key on

code error NH 4128 Remote No.3 No control Message Received

code error NH 4129 Remote No.3 Control Message not plausible

code error NH 4130 Remote No.3 EEPROM Error

code error NH 4131 Remote No.3 Switched to failsafe

code error NH 4132 Remote No.3 Under voltage

code error NH 4133 Remote No.3 Over voltage

code error NH 4134 Remote No.3 Spool movement to low

code error NH 4135 Remote No.3 Spool movement to high

code error NH 4136 Remote No.3 Float position not reached

code error NH 4137 Remote No.3 Manually operated

code error NH 4138 Remote No.3 Driver faulty

code error NH 4139 Remote No.3 potentiometer faulty.

code error NH 4140 Remote No.3 Unable to reach neutral

code error NH 4141 Remote No.3 Spool not in neutral at key on

code error NH 4142 Remote No.4 No control Message Received

code error NH 4143 Remote No.4 Control Message not plausible

code error NH 4144 Remote No.4 EEPROM Error

code error NH 4145 Remote No.4 Switched to failsafe

code error NH 4146 Remote No.4 Under voltage

code error NH 4147 Remote No.4 Over voltage

code error NH 4148 Remote No.4 Spool movement to low

code error NH 4149 Remote No.4 Spool movement to high

code error NH 4150 Remote No.4 Float position not reached

code error NH 4151 Remote No.4 Manually operated

code error NH 4152 Remote No.4 Driver faulty

code error NH 4153 Remote No.4 potentiometer faulty.

code error NH 4154 Remote No.4 Unable to reach neutral

code error NH 4155 Remote No.4 Spool not in neutral at key on

code error NH 4156 Remote No.5 Spare

code error NH 4157 Remote No.5 Spare

code error NH 4158 Remote No.5 Spare

code error NH 4159 Remote No.5 Spare

code error NH 4160 Remote No.5 Spare

code error NH 4161 Remote No.5 Spare

code error NH 4162 Remote No.5 Spare

code error NH 4163 Remote No.5 Spare

code error NH 4164 Remote No.5 Spare

code error NH 4165 Remote No.5 Spare

code error NH 4166 Remote No.5 Spare

code error NH 4167 Remote No.5 Spare

code error NH 4168 Remote No.5 Spare

code error NH 4170 EHR Control No. 1 not calibrated

code error NH 4171 EHR Control No.1 open circuit

code error NH 4172 EHR Control No.1 short circuit

code error NH 4173 EHR Control No. 2 not calibrated

code error NH 4174 EHR Control No.2 open circuit

code error NH 4175 EHR Control No.2 short circuit

code error NH 4176 Timer Switch No.1 / No.2 not connected

code error NH 4177 EHR Control No. 3 not calibrated

code error NH 4178 EHR Control No.3 open circuit

code error NH 4179 EHR Control No.3 short circuit

code error NH 4180 EHR Control No. 4 not calibrated

code error NH 4181 EHR Control No.4 open circuit

code error NH 4182 EHR Control No.4 short circuit

code error NH 4183 Timer Switch No.3 / No.4 not connected

code error NH 4184 EHR Joystick potentiometer X open circuit.

code error NH 4185 EHR Joystick potentiometer X short circuit.

code error NH 4186 EHR Joystick potentiometer Y open circuit.

code error NH 4187 EHR Joystick potentiometer Y short circuit.

code error NH 4190 No communications from (EHR) No.1.

code error NH 4191 No communications from ( EHR) No.2.

code error NH 4192 No communications from ( EHR) No.3.

code error NH 4193 No communications from ( EHR) No. 4.

code error NH 4194 Motor mode No.1 switch faulty

code error NH 4195 Motor mode No.2 switch faulty

code error NH 4196 Motor mode No.3 switch faulty

code error NH 4197 Motor mode No. 4 switch faulty

code error NH 5001 Rear PTO Brake Solenoid stuck off

code error NH 5002 Rear PTO Brake Solenoid stuck on

code error NH 5003 Rear PTO Brake output open circuit

code error NH 5004 Rear PTO Brake driver over temperature ( not used )

code error NH 5005 Brake switch open circuit

code error NH 5007 Rear PTO Solenoid Stuck off

code error NH 5008 Rear PTO solenoid circuit overcurrent

code error NH 5024 Rear PTO not calibrated

code error NH 5027 Rear PTO speed sensor open circuit (not implemented)

code error NH 5033 Rear PTO cab N/C switch open circuit

code error NH 5034 Rear fender PTO switch open / short to ground.

code error NH 5035 Rear fender PTO switch input short to +12v

code error NH 5036 PTO failure to Start

code error NH 5037 Rear PTO cab N/O switch stuck closed

code error NH 5038 Cab & fender PTO switches operated in 2 sec

code error NH 5039 Incorrect voltage on fender PTO switch

code error NH 5040 Rear fender PTO switches reversed ( not used )

code error NH 5041 PTO disengaged due to assuasive load ( not used )

code error NH 5042 PTO Management switch shorted

code error NH 5099 Auto PTO mode not enabled

code error NH 6020 FWD switch error

code error NH 6021 FWD Solenoid Stuck on

code error NH 6022 FWD Solenoid Stuck off

code error NH 6023 FWD solenoid open circuit

code error NH 7014 Difflock switch error

code error NH 7015 Difflock Solenoid Stuck off

code error NH 7016 Difflock Solenoid Stuck on

code error NH 7017 Difflock solenoid open circuit

code error NH 7018 Difflock driver over temperature

code error NH 7024 Steering angle sensor not calibrated

code error NH 7031 Steering angle sensor out of Maximum range

code error NH 7032 Steering angle sensor out of Minimum range

code error NH 8007 Front PTO Solenoid Stuck on

code error NH 8008 Front PTO solenoid open circuit

code error NH 8024 Front PTO not calibrated

code error NH 8027 Front PTO speed sensor open circuit

code error NH 8033 Front PTO cab N/C switch open circuit

code error NH 8036 Front PTO failure to Start

code error NH 8037 Front PTO cab N/O switch stuck closed

code error NH 8099 Front PTO option not enabled

code error NH 9001 Front HPL (High Pressure Lift) Potentiometer open circuit.

code error NH 9002 Front HPL (High Pressure Lift) Potentiometer short circuit.

code error NH 10001 Upper lockout Solenoid error

code error NH 10002 Raise Solenoid error

code error NH 10003 Lower Solenoid error

code error NH 10004 Front Axle Potentiometer above threshold

code error NH 10005 Front Axle Potentiometer below threshold

code error NH 10007 Go up error, Suspension Unable to return to set point

code error NH 10008 Go down error, Suspension Unable to return to set point

code error NH 10009 Lower lockout Solenoid Error

code error NH 10024 Front Suspension not calibrated

code error NH 10099 Front Suspension mode not enabled

code error NH 14001 Rear PTO speed short to VCC or open circuit

code error NH 14002 Rear PTO speed short to Ground

code error NH 14011 Engine speed sensor short to VCC or open circuit

code error NH 14012 Engine speed sensor short to Ground

code error NH 14015 The ADIC 5 volt reference voltage is too low - below 4 volts

code error NH 14016 The ADIC 5 volt reference voltage is too high - above 6 volts

code error NH 14021 Radar Ground speed short to VCC or open circuit

code error NH 14022 Radar Ground speed short to Ground

code error NH 14031 Front PTO speed short to VCC or open circuit

code error NH 14032 Front PTO speed short to Ground

code error NH 14041 Engine coolant temp short to VCC or open circuit

code error NH 14042 Engine coolant temp short to Ground

code error NH 14051 Fuel level sensor short to VCC or open circuit

code error NH 14052 Fuel level sensor short to Ground

code error NH 14061 Air brake pressure short to VCC or option set but sensor not connected

code error NH 14071 Front Hitch Position short to 12 or 5 Volts

code error NH 14072 Front Hitch Position short to Ground or open circuit

code error NH 14081 Engine oil pressure short to 12 or 5 Volts

code error NH 14082 Engine oil pressure short to Ground or open circuit

code error NH 14091 Transmission output speed short to VCC or open circuit

code error NH 14092 Transmission output speed short to Ground

code error NH 14100 Air brake pressure not configured

code error NH 14101 Fuel contaminated sensor Not connected

code error NH 14200 EEPROM error

code error NH 14900 Transmission module missing (DA/DB/DE/DF).

code error NH 14901 Engine controller not present (EDC7)

code error NH 14902 Auxiliry (optional) Controller Module missing (DD/DH).

code error NH 14903 SCM controller missing (GA 12x12 only).

code error NH 14904 Arm Rest Module (ARU) missing. (Steyr 16x16 only)

code error NH 14905 KEYPAD missing

code error NH 14906 Fast Steer Controller (KA) missing.

code error NH 14907 DOG (Display Of Gears) missing.

code error NH 15001 Exceeding safe operating wheel speed (10 km/h) with system still enabled or still active. Error code not active fast steer lamp flashes instead.

code error NH 15002 Steering wheel control proximity sensor open circuit.

code error NH 15003 Steering wheel control proximity sensor short circuit.

code error NH 15006 Split valve LVDT open circuit.

code error NH 15007 Split valve LVDT short circuit.

code error NH 15008 Change valve Solenoid open circuit

code error NH 15009 Change valve Solenoid short circuit across

code error NH 15010 Safety switch Fail

code error NH 15011 Maximum engagement time (5 minutes) elapsed.

code error NH 15012 Split Valve spool stuck open

code error NH 15013 Change valve or Split valve spools Stuck closed.

code error NH 15014 Split Valve spool stuck in transition zone cant identify which steering mode the tractor is definitely in.

code error NH 15015 Cold oil, temperature below 5 degrees C. Error code not active fast steer lamp flashes instead.

code error NH 15024 System not calibrated.

Despiece Tractores - Parts list 

Camion

Moto

Moteur bateau 

Vintage   Machinery

bottom of page